Contents12 sections
This guide was first published in German on handgetestet.de.
With car phone mounts, the car comes first and the phone second. If you start with watts and magnet strength, you often end up at home facing round vents the clip won’t fit into, or a phone that blocks the speedometer. For a current iPhone, a magnetic 15-watt Qi2 mount is usually the most convenient solution. For an Android phone without a magnet, or if the mount only needs to hold the phone, a classic clamp mount is a better fit.
Step one: where should the phone go?
There are three options. On the air vent, the phone hangs close to your line of sight, and installation takes seconds. What matters there are the slats. For its Qi2 mount, Belkin specifies slats up to 3 mm thick and 20 mm deep, while Peak Design requires at least 8 mm of spacing between slats. Round or curved vents, as found in many small cars, rule out almost all vent mounts.
Then there’s winter. The heater blows warm air straight onto the battery, and Belkin itself advises closing that vent when the heat is on.
On the dashboard, you use a suction cup or an adhesive pad. That’s more stable, but it doesn’t work on every surface. Anker excludes leather and suede for its adhesive base, and iOttie recommends the windshield for leather dashboards. On the windshield, a suction cup holds almost anywhere, but the device must not hang in your field of view there. It’s better placed at the bottom left or right edge than in the middle behind the mirror, where a dash cam is often already stuck.
Step two: charge or just hold?
Qi2 comes with magnets that align the charging coil. According to the manufacturers, the mounts below charge at up to 15 watts. But that only works if the power adapter in the cigarette lighter socket delivers at least 20 watts; an old USB-A adapter slows everything down.
And the case? Only cases with a magnetic ring hold magnetically. ESR gives cases under 2 mm as the limit, Anker under 2.5 mm. Which cases work is covered in our guide to iPhone cases (in German). That leaves the cable question. Permanently attached cables look tidy. If one breaks, you can’t replace it.
Step three: keep the rules in mind
German law doesn’t require a mount. But a mount makes it easy to follow the rules. Under § 23 (1a) of the German road traffic regulations (StVO), anyone driving a vehicle may only use a phone or navigation device if they neither pick it up nor hold it in their hand to do so. Voice control or a brief glance appropriate to the traffic situation is then allowed. Extended tapping remains off-limits, even with the phone in a mount. The exception only applies when the car is stationary and the engine is completely off. The automatic start-stop system at a traffic light explicitly does not count. Paragraph 1 also makes you responsible for ensuring that devices don’t restrict your view. Large mounts in the middle of the windshield don’t fit well with that.
Six mounts on the shortlist
| Model | Mounting | Charging (manufacturer specs) | Best for |
|---|---|---|---|
| Belkin BoostCharge Pro Qi2 15W (WIC008 v2) | Air vent | Qi2, up to 15 W, 20 W car adapter included | iPhone users with flat, straight slats |
| ESR Qi2 car charger with CryoBoost (HaloLock) | Air vent | Up to 15 W, with fan | Frequent drivers with navigation running constantly |
| Anker Nano Wireless Car Charger (A2216) | Dashboard, adhesive base | Qi2, up to 15 W, 25 W adapter included | Cars with round vents |
| iOttie Velox Mini Qi2 Dash & Windshield | Suction cup, windshield or dashboard | Qi2, up to 15 W | Anyone who wants flexible mounting |
| Peak Design Car Vent Mount Charging Qi2 | Air vent | Qi2, up to 15 W | Users already in the Peak Design system |
| iOttie Easy One Touch 6 Dash & Windshield | Suction cup, clamp holder | No wireless charging | Android without a magnet, small budget |
Belkin BoostCharge Pro Qi2 15W
Everything comes in one box: the mount, a permanently attached 1.5 m USB-C cable and a 20 W adapter for the car’s power socket. The phone sits in portrait or landscape. The slat specifications are tight, so measure first. According to Belkin, straight, horizontal slats work best.
ESR Qi2 with CryoBoost
A fan makes the difference. According to ESR, it kicks in while charging and switches off as soon as the battery is full. That makes sense, because heat is the main reason wireless charging slows down in the car. In very quiet cars you can hear the whirring, ESR admits. The mount doesn’t support round vents.
Anker Nano Wireless Car Charger
Instead of clipping to the vent, the Anker sits on a large adhesive base. A flexible arm made of shape-memory alloy is designed to adapt to curved dashboards too, and a 25 W adapter is included. The pad is detachable. The adhesive, however, only holds once, and cases without a magnet don’t work. That makes it unsuitable if you switch cars frequently.
iOttie Velox Mini Qi2 Dash & Windshield
iOttie’s Qi2 version attaches with a gel suction cup to the windshield or to an included pad on the dashboard. According to the product page, its telescopic arm extends from about 10 to 17 cm. That moves the phone out of your field of view while keeping it within easy reach. According to iOttie, it’s designed for Qi2 phones and MagSafe iPhones from the 12 series onward.
Peak Design Car Vent Mount Charging Qi2
Aluminum, a swivel arm and unusually clearly documented limits: slats 7 to 23 mm deep, no more than 3.2 mm thick, no round or curved vents. According to Peak Design, it charges phones without Qi2 at only 5 watts. Full holding power requires the company’s own cases or the Universal Adapter. Expensive. The system can pay off if you already use Peak Design on your bike or tripod.
iOttie Easy One Touch 6
No magnets, no charging. In return, almost any phone fits. When the phone presses the trigger, the arms close on their own, according to the manufacturer, and you open them with one hand. The USB port stays free, and a cable clip is built in. Often, that’s exactly enough.
How we would decide
An iPhone, straight slats and no appetite for tinkering: then it’s the Belkin BoostCharge Pro Qi2, because the power adapter is included. Long drives with navigation and a heavy load favor the ESR with CryoBoost because of its fan.
Round vents, or a vent that’s in the way? Then the Anker Nano for the dashboard or the iOttie Velox Mini Qi2 for the windshield. Peak Design’s Vent Mount only makes sense if you already have a Peak Design case. For an Android phone without a magnetic ring, or for the second car, the iOttie Easy One Touch 6 and a cable will do.
One more thing about charging. In summer behind the windshield, every phone throttles at some point, no matter which mount it’s in. So if you navigate a lot, the charging cable is still useful. The matching chargers for home are in our MagSafe charger guide (in German).
If you’d rather not hold the phone at all and control it via the screen in the dashboard instead, you’ll find suitable devices in our guide to the car stereo with CarPlay.
The OOONO Co-Driver promises warnings from the community; why it didn’t convince us is explained in our review of the OOONO Co-Driver NO2.
Frequently asked questions
Where should a phone mount go in the car?
There are three options: the air vent, the dashboard and the windshield. On the vent, the phone sits close to your line of sight, and the slats are what matter. On the windshield, it's better placed at the bottom left or right edge than in the middle, because it must not hang in your field of view.
Does a vent mount fit round air vents?
Round or curved vents rule out almost all vent mounts. Belkin specifies slats up to 3 mm thick and 20 mm deep, and Peak Design at least 8 mm of spacing between slats. With round vents, a dashboard or windshield mount is the alternative.
What do you need for Qi2 to charge at 15 watts in the car?
A power adapter in the cigarette lighter socket that delivers at least 20 watts; an old USB-A adapter slows everything down. You also need a case with a magnetic ring that is thin enough: ESR gives under 2 mm as the limit, Anker under 2.5 mm. Belkin and Anker include a suitable power adapter.
What does German traffic law allow with a phone in a mount?
Under § 23 (1a) of the German road traffic regulations (StVO), a driver may only use a phone if it is neither picked up nor held for that purpose. Voice control or a brief glance is allowed; extended tapping remains off-limits. The exception only applies when the car is stationary and the engine is completely off; start-stop does not count.
Why does my phone charge so slowly wirelessly in the car?
Heat is the main reason. In summer behind the windshield, every phone throttles at some point, and in winter the heater blows warm air onto the battery. The ESR mount with CryoBoost has a fan for this reason. If you navigate a lot, the charging cable is still useful.
Does an adhesive mount stick to every dashboard?
No. Anker excludes leather and suede for its adhesive base, and iOttie recommends the windshield for leather dashboards. With the Anker Nano, the adhesive also only holds once, so it isn't suitable if you switch cars frequently.
Sources
- § 23 StVO, German road traffic regulations, Gesetze im Internet (German Federal Ministry of Justice)
- Belkin: BoostCharge Pro Magnetic Wireless Car Charger with Qi2 15W
- Belkin Support: FAQ on the WIC008 v2
- ESR: Qi2 Wireless Car Charger with CryoBoost (HaloLock)
- ESR Help: 15W Wireless Car Charger with CryoBoost
- Anker: Nano Wireless Car Charger (A2216)
- iOttie: Velox Mini Qi2 Wireless Dash & Windshield Mount
- iOttie: Easy One Touch 6 Dash & Windshield Mount
- Peak Design: Car Vent Mount
Where to buy
- Belkin BoostCharge Pro Qi2 15W Kfz-HalterungCheck price at Amazon.deAvailable in Germany: Amazon.de
- ESR Qi2 Kfz-Ladegerät mit CryoBoost (HaloLock)Check price at Amazon.deAvailable in Germany: Amazon.de
- Anker Nano Wireless Car Charger (A2216)Check price at Amazon.deAvailable in Germany: Amazon.de
- iOttie Velox Qi2 Mini Dash & WindshieldCheck price at Amazon.deAvailable in Germany: Amazon.de
- Peak Design Car Vent Mount Charging Qi2Check price at Amazon.deAvailable in Germany: Amazon.de
- iOttie Easy One Touch 6 Dash & WindshieldCheck price at Amazon.deAvailable in Germany: Amazon.de
