Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdicts1.730 Ratgeber und Tests How we test
handgetestet

Deutsch

GARDEBRUK Foldable Robot Mower Garage Review: An Assembly Full of Hurdles

We assembled GARDEBRUK's foldable metal robot mower garage: sharp-edged sheet metal, tedious screwing, incomplete instructions and holes in the roof frame that didn't line up. One star out of five.

Christian Blank · handgetestet editorial team · November 16, 2026
Green GARDEBRUK metal robot mower garage, assembled without a roof on a paved areaImage: handgetestet.de

This review was first published in German on handgetestet.de.

GARDEBRUK’s robot mower garage is a freestanding metal shelter with a lean-to roof that, according to the manufacturer, can be folded open. It is meant to protect the robot mower and its charging station from rain, hail and sun. We assembled the green version, measuring 89 × 90 × 54 cm, in the garden. Our impression: the assembly was tedious, the instructions were incomplete, and the holes in the roof didn’t line up. One star out of five.

Technical data

All values in the table are GARDEBRUK’s specifications from the product page, as of November 14, 2026. We did not measure them ourselves. What we experienced ourselves is described in the sections below.

Dimensions89 × 90 × 54 cm (length × width × height)
Footprint77 × 85 cm
Materialhot-dip galvanized metal
Rooflean-to roof, sloping toward the back, opens with two gas springs
Cablecable entry with rubber protection
Edgesedge protection on all edges
Anchoring4 ground stakes for lawns; on paving or concrete with standard screws
Colorgreen
Item numberDB-109177

Assembly: gloves and a second person

We followed the instructions during assembly. The very first parts made it clear: the sheet metal is very sharp-edged. We wouldn’t start without work gloves. According to the manufacturer, the finished garage has edge protection everywhere. During assembly, however, we were dealing with the raw sheet metal.

The structure is unstable at first and vulnerable to wind. A second person is really needed to hold the walls. It’s best to assemble it on a calm day, because the large sheet-metal surfaces catch the wind like a sail.

Green roof panel of the GARDEBRUK garage with a gray crossbar in the frame, lying on the lawn, next to it the instructions weighed down with stones
The roof panel with its brace before assembly. The instructions lie next to it, weighed down, since even a light wind is enough.

Dozens of screws into thin sheet metal

The real test of patience is screwing the thin sheet-metal walls to the braces. There are dozens of screws that have to be driven into thin sheet metal. By hand, that’s torture; a cordless drill is essential. After about 90 minutes, our box with its four walls was standing.

GARDEBRUK robot mower garage seen from above without a roof: green trapezoidal sheet-metal walls with a light frame on paving
The box is standing: walls made of trapezoidal sheet metal, on top the light frame that the lean-to roof is supposed to sit on.

The lean-to roof: steps missing, holes don’t line up

Next comes the lean-to roof, and this is where it got frustrating. The instructions are faulty at this point: the first assembly steps for the roof are missing. We had to puzzle over it for a while until it was clear how to continue. Then the next problem: the drill holes in the roof frame didn’t line up with their counterparts.

That’s why we can’t judge how the folding roof with its gas springs holds up in everyday use. We never got that far with this garage.

Corner of a light frame part of the GARDEBRUK garage with two drill holes, lying on the lawn
Corner of a frame part with drill holes.
Close-up of a frame corner of the GARDEBRUK garage with scratches and chips in the light paint
A frame corner up close: scratches and chips in the paint.

Stability, ground anchors and protective film

Three more things bothered us:

  • The structure remained wobbly and vulnerable to wind.
  • The included ground anchors are not suitable for a firm hold.
  • The wafer-thin protective film on the sheet metal only comes off with a lot of patience.

There is one piece of good news: the screws can be backed out again. If you’re not happy with the result, you can take the garage apart again.

Promise and practice

GARDEBRUK describes the garage as a high-quality shelter made of hot-dip galvanized metal, with edge protection against injuries, well-thought-out cable routing and a foldable roof. The idea behind the folding roof is good: the buttons on the mower should stay within reach while it sits in the station. Our impression from the assembly doesn’t match this claim. Sharp edges, instructions with gaps and holes that don’t line up point to careless manufacturing or quality control.

If you try it anyway: our assembly tips

If you decide on this or a similar sheet-metal garage, a little preparation will save you some trouble. From our assembly, we recommend this order:

  • Read the entire instructions before you start, especially the pages about the roof. If something is missing there, you’ll notice before assembly and not halfway through.
  • Lay out the roof frame parts side by side beforehand and check whether the holes line up with their counterparts.
  • Put on work gloves before the sheet metal comes out of the packaging.
  • Assemble with two people on a calm day, and weigh down loose panels and the instructions.
  • Use the cordless drill at a low torque setting so the screws don’t strip in the thin sheet metal.
  • Peel off the protective film while the parts are still lying flat, if possible.

Who is the garage for?

At best, it suits people who enjoy improvising, are confident with a cordless drill and a power drill, assemble it with two people and are willing to fix things themselves. It’s not suitable for anyone who wants to set up a garage by following the instructions and then be done with it.

What you should know before buying a metal garage

  • Measure your mower and charging station. According to the manufacturer, the footprint is 77 × 85 cm, and the entrance has to match the way the mower approaches the station.
  • Plan for two people, gloves, a cordless drill and a calm day.
  • On a lawn, ground stakes hold a light sheet-metal cover only to a limited extent. Paving stones or a concrete base you can screw into is the safer choice.
  • If your mower navigates by satellite, check the reception under metal. Under a different metal garage, our Segway Navimow i105 lost its satellite reception.

Alternatives

Which garages are available and why a garage from your mower’s own manufacturer is usually the easiest choice is covered in our guide Buying a robot mower garage (in German). Why metal above a mower with satellite positioning can be tricky is explained in our guide Robot mower navigation (in German). A garage also doesn’t replace winter storage; more on that in our guide Storing a robot mower over winter (in German). And against the grass that is left standing around every garage, a set edge helps; see Robot mowers and lawn edging (in German).

Our verdict

The foldable GARDEBRUK garage promises a high-quality shelter with a practical folding roof. For us, little of that remained: sharp-edged sheet metal, a wobbly structure that only works with two people on a calm day, tedious screwing into thin sheet metal, instructions with gaps and a roof frame whose holes didn’t line up. On top of that, ground anchors we don’t trust to hold firmly. Our rating: one star out of five.

Frequently asked questions

How long does it take to assemble the GARDEBRUK robot mower garage?

For us, the box with its four walls was standing after about 90 minutes. Then comes the lean-to roof, where steps are missing from the instructions. So plan for considerably more time.

Do you need tools and help for the assembly?

Yes. The sheet metal is very sharp-edged, so gloves are a must. Dozens of screws go into thin sheet metal, and a cordless drill is essential. A second person should hold the walls, ideally on a day without wind.

Does the roof of the GARDEBRUK garage fit?

Not for us. The first assembly steps for the lean-to roof were missing from the instructions, and the holes in the roof frame didn't line up.

How does the garage stand on the lawn?

According to the manufacturer, four ground stakes are included; on paving or concrete, you screw it down. In our opinion, the ground anchors don't hold firmly enough, and the structure remained vulnerable to wind.

How big is the garage?

According to the manufacturer, it measures 89 × 90 × 54 cm, and the footprint inside is 77 × 85 cm. Measure your mower and charging station beforehand.

Sources

Are you a manufacturer or retailer and would like us to test your product? Offer a product for testing (in German).

Conclusion

According to the manufacturer, the garage offers a solid shelter with a foldable lean-to roof and edge protection. During our assembly, the sheet metal was sharp-edged, the walls were hard to hold without a second person and screwing into thin sheet metal was tedious. Steps for the lean-to roof were missing from the instructions, and the holes in the roof frame didn't line up. One star out of five.

Where to buy

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.