Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdicts1,732 guides and reviews in German How we test
handgetestet

Deutsch

Microphone Boom Arm 2026: Mic Arms with Desk Clamp

Microphone boom arms compared for 2026: load capacity, desk clamp, cable management and low profile. RØDE PSA1+, Elgato Wave Arm, Shure by Gator and K&M at a glance.

handgetestet editorial team · Updated November 17, 2026
Elgato Wave Mic Arm LPImage: Coolblue (Pressebild)
Contents13 sections

This guide was first published in German on handgetestet.de.

According to its data sheet, a Shure SM7B weighs 764 grams. The 23850 desk arm from König & Meyer is designed for 0.8 kilograms, and that does not yet include the mount, threaded adapter and heavy XLR cable. That is exactly how you end up with arms that slowly sag. Our recommendation for most desks is therefore the RØDE PSA1+, which according to RØDE holds microphones from 94 grams to 1.2 kilograms and reaches up to 94 centimeters. If you sit in front of a camera and do not want the arm in the frame, take a look at the Elgato Wave Mic Arm LP.

Which microphone suits your voice is covered in our buying advice for podcast microphones (in German). Here, it is about what the microphone hangs on.

Why the springs have to match the microphone

An articulated arm does not hold the microphone in place with clamping screws but with springs that pull against the weight at the end of the arm. If the load is too heavy, gravity wins. If it is too light, the arm springs upward. That is why good manufacturers state not just an upper limit but a range.

Be honest with the math. On top of the microphone come the shock mount or holder, a pop filter and the cable that also hangs from the head of the arm. If in doubt, put everything together on the kitchen scale. A light USB microphone, on the other hand, can fall below the minimum load, which Elgato specifies as 200 grams for the Wave Mic Arm MK.2.

Then there is leverage. The further you extend the arm, the harder the same microphone pulls on the joints and clamp. An arm working right at its limit often only holds in a steep position. Better to plan for a 20 to 30 percent reserve.

Look under the desk first

Most arms are attached to the edge of the desk with a screw clamp. With a 25-millimeter particleboard top, any clamp fits. Solid wood tops 40 millimeters thick, a protruding apron or a crossbar directly at the edge are the more common obstacles. According to the manufacturer, the K&M 23850 clamps 10 to 51 millimeters, the arms from Shure by Gator up to 55 millimeters, Elgato up to 60 millimeters and RØDE’s PSA1+ up to 70 millimeters.

One alternative is a screw-in mount. For this, you drill a hole in the desktop, and the arm stands firmly where you want it, even in the middle of the desk. RØDE includes such a mount with the PSA1+ for tops up to 55 millimeters, and K&M offers the 23855 desk flange as an accessory.

If you work at a height-adjustable desk, leave a slack loop in the cable. Otherwise, the first trip up will yank the connector out of the interface.

Cable in a channel or loose alongside

A cable dangling freely down from the microphone looks messy and transmits every bump against the arm as noise. That is why the arms from RØDE, Elgato and Shure by Gator route the cable along the arm, each in its own way. On the LP, Elgato relies on channels with magnetic covers; on the MK.2, on channels at the top of the arm into which the cable is pressed. Shure by Gator uses clips on the SH-BROADCAST1 and a magnetic channel on the flat SH-BROADCAST2. König & Meyer ships the 23850 with a five-meter XLR cable included.

Before buying, check whether your connector fits. Right-angle USB-C plugs and thick XLR cables are not equally well accommodated everywhere. For microphones with the connector at the rear end, such as the SM7B, Shure by Gator offers a thread extension that keeps the connector away from the joint.

Flat arm or high arc?

Tall spring arms first rise upward and then come down to the mouth from above. In front of a webcam, such an arc visibly sticks into the frame. Low-profile arms, on the other hand, run flat across the desktop and come from below or from the side. According to Elgato, the Elgato Wave Mic Arm LP stays 70 millimeters above the desktop with the lower arm and 160 millimeters with the upper arm. Shure by Gator describes the SH-BROADCAST2 as an arm that stays below the shoulder line.

The compromise lies in the height. Flat arms do not reach very high. If you present standing up or want a large microphone to hover over a keyboard, a spring arm serves you better. For video calls and streams in front of the webcam (in German), the flat arm is usually the tidier choice.

Six microphone arms and their key specs

ModelLoad capacity according to manufacturerReachClamp up toBest for
RØDE PSA1+94 g to 1.2 kg94 cm horizontal, 86 cm vertical70 mm, screw-in mount up to 55 mmBroadcast microphones, light USB microphones
Elgato Wave Mic Arm LPup to 2 kg74 cm horizontal60 mmStreams and calls on camera
Elgato Wave Mic Arm MK.2200 g to 1.2 kg95 cm horizontal, 85 cm vertical60 mmdeep desks, high position
Shure by Gator SH-BROADCAST14 lbs (around 1.8 kg)94 cm55 mmSM7B, MV7 and other heavy microphones
Shure by Gator SH-BROADCAST23 lbs (around 1.4 kg)84 cm55 mmflat setup with a Shure microphone
K&M 238500.8 kg46 to 96 cm51 mmlight studio microphones, cable included

RØDE PSA1+

According to RØDE, the PSA1+ has damped internal springs, a neoprene sleeve and rubberized contact points against knocking noises from the keyboard and mouse. The load range of 94 grams to 1.2 kilograms is wide enough for a light USB microphone as well as an SM7B with its cable. The clamp and screw-in mount are included, as is a 3/8-inch to 5/8-inch adapter. At 1.52 kilograms of its own weight, it is no lightweight, but at a fixed workstation that does not matter.

Elgato Wave Mic Arm LP

Flat, made of metal, with a ball head at the end. Elgato lists a load of up to 2 kilograms including accessories and a horizontal reach of 74 centimeters. According to the manufacturer, the elbow joint tilts 90 degrees up and 60 degrees down. It is not made for recording while standing.

Elgato Wave Mic Arm MK.2

According to the manufacturer, Elgato’s spring arm reaches 95 centimeters out and 85 centimeters up, and a 15-centimeter extension is included. If you have to position a microphone over a deep desk or behind a wide monitor, that gives you room to play with. Pay attention to the lower limit of 200 grams; very light microphones fall below it.

Shure by Gator SH-BROADCAST1

Made by Gator under license from Shure. The powder-coated steel arm rotates 360 degrees, and the cable runs in a channel with clips. The thread extension creates space for the XLR connector of the SM7B, SM7dB and the MV7 series. If you already own one of these microphones, you get the matching counterpart from the same manufacturer here.

Shure by Gator SH-BROADCAST2

According to Shure, the flat version with a magnetic cable channel reaches up to 84 centimeters and lets the upper arm swivel 90 degrees. Besides the clamp, there is a mount for drilling through the desktop. In its spec table, Gator states 3 lbs, or around 1.4 kilograms. That leaves enough headroom for an SM7B with its cable.

K&M 23850

The desk arm from König & Meyer, based in Wertheim, Germany, is made of steel, adjusts between 46 and 96 centimeters and comes with a five-meter XLR cable. The load capacity of 0.8 kilograms is tight. It works well for a light condenser microphone, but for an SM7B with a shock mount we would choose a different arm.

Which arm suits which microphone

  • You speak into a heavy dynamic microphone and sit without a camera: RØDE PSA1+. With a Shure microphone, the SH-BROADCAST1 makes just as much sense.
  • You stream or take calls on video: Elgato Wave Mic Arm LP, or the SH-BROADCAST2 for Shure microphones.
  • The desk is deep or the microphone should come from above: Elgato Wave Mic Arm MK.2.
  • A light studio microphone, and you need a cable anyway: K&M 23850.

No microphone yet? Then take a look at our guide to USB microphones for streaming (in German) first. The weight of the microphone decides the arm, not the other way around.

We tried out a heavy microphone for the arm ourselves: our review of the RØDE PodMic USB explains where it convinces and where it does not.

Frequently asked questions

How much does a microphone arm need to hold?

Add up the microphone, shock mount or holder, pop filter and cable, and if in doubt, put it all on the kitchen scale. A Shure SM7B alone weighs 764 grams. The further the arm is extended, the harder the load pulls. Plan for a 20 to 30 percent reserve and also pay attention to the minimum load.

Will the desk clamp fit my desk?

With a 25-millimeter particleboard top, any clamp fits. The obstacles are more likely thick solid wood tops, aprons or crossbars at the edge. The K&M 23850 clamps up to 51 millimeters, Shure by Gator up to 55, Elgato up to 60 and the RØDE PSA1+ up to 70 millimeters. Alternatively, there are screw-in mounts for a hole in the desktop.

Flat microphone arm or spring arm with a high arc?

Tall spring arms come down to the mouth from above and visibly stick into the frame in front of a webcam. Low-profile arms such as the Elgato Wave Mic Arm LP or the Shure by Gator SH-BROADCAST2 run flat across the desktop. In return, they do not reach very high; for recording while standing, a spring arm is the better fit.

Which microphone arm suits the Shure SM7B?

The RØDE PSA1+ holds the SM7B including its cable. With a Shure microphone, the SH-BROADCAST1 makes just as much sense; its thread extension creates space for the XLR connector at the rear end. We would not use the K&M 23850 with its 0.8-kilogram capacity for an SM7B with a shock mount.

Where does the microphone cable go on the arm?

A freely dangling cable looks messy and transmits bumps as noise. The arms from RØDE, Elgato and Shure by Gator route it along the arm in channels or clips. On a height-adjustable desk, leave a slack loop, or the first trip up will yank the connector out.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.