Contents15 sections
This guide was first published in German on handgetestet.de.
The box of a sand filter almost always shows the biggest number the manufacturer could measure. Less of it reaches the pool. If you run an above-ground pool with 20 to 35 cubic meters, the manufacturer data suggests a unit the size of the Steinbach Comfort 75 will serve you well: 7,800 liters of circulation per hour with a filled tank, a self-priming pump and a pre-filter. For small pools up to about 15 cubic meters, considerably less is enough.
This guide explains how to calculate the right capacity for your pool, when filter glass makes more sense than sand and what actually happens during backwashing. If you are still choosing the pool itself, start with our guide to pools (in German).
Pump rate is not circulation rate
A sand filter system consists of two parts. The pump draws water in through the skimmer and pushes it from above through the sand bed in the tank. At the bottom, a screen collects the filtered water, which flows back into the pool through the multiport valve. The sand slows things down. The denser and dirtier the filter bed, the less water gets through.
That is why Steinbach separates the figures cleanly: the pump of the Comfort 75 moves 9,400 liters per hour in free flow, while 7,800 liters run through the filled tank. For the Intex Krystal Clear 26648, the data sheet lists 10,500 and 8,000 liters. The smaller value always counts for the calculation, meaning what actually flows through with a filled tank. Bestway gives a single flow figure per unit. Plan with a deduction there.
How to calculate the right size
Steinbach states in its manual that the entire water volume should pass through the filter at least twice within 24 hours, and three to five times for a heavily used pool. Hayward recommends 10 to 14 filter hours a day for normal operation. This yields a simple rule of thumb: pool volume in cubic meters divided by six gives the required circulation rate in cubic meters per hour if the pump is to run for twelve hours.
A round pool with a diameter of 4.57 meters and a water level of 1.10 meters holds about 18 cubic meters. So it needs around 3 cubic meters per hour. A steel-wall pool with a diameter of 5.50 meters and a water level of 1.20 meters comes to just over 28 cubic meters and thus to just under 5 cubic meters per hour. Calculate with the water level, not the wall height.
This calculation lets you check the maximum pool size claims. According to Steinbach, the Comfort 75 is designed for 40,000 liters; two passes take just over ten hours there. For the Intex 26648, Steinbach as distributor states 57,500 liters. At a circulation rate of 8,000 liters, this pool needs over 14 hours for two passes. That is possible. It just leaves no margin for hot weeks with a full pool.
Sand, glass or filter balls?
Quartz sand is the standard medium. The grain size is specified by the unit, and it varies considerably by manufacturer: Steinbach requires 0.7 to 1.2 millimeters to DIN EN 12904 (the European standard for filter sand) for the Comfort series, Bestway 0.45 to 0.85 millimeters for its Flowclear units. Play sand or beach sand does not belong in the tank, Bestway states explicitly, because grain size and purity are wrong. Steinbach recommends changing the sand every two to three years.
Filter glass made from recycled glass goes into the same tank. Steinbach describes it as filtering slightly finer than sand, needing less water for backwashing and lasting about four years, roughly twice as long as sand. In return, the manufacturer cites higher purchase costs. By weight you need less: Intex specifies 23 kilograms of sand or 16 kilograms of glass for its 12-inch sand filter. If you have to replace the media anyway and don’t want to flood your yard with several hundred liters at every backwash, glass is a good choice.
Polyethylene filter balls are a different concept. According to Steinbach, 700 grams replace 25 kilograms of sand, which saves the hauling. They must not be backwashed; they are washed by hand, at least once a season. And flocculants are off-limits because they make the balls clump. If you like to use flocculant, stick with sand.
Backwashing: when, how long, where the water goes
The pressure gauge tells you when. Note the pressure with a freshly backwashed filter. If it rises by 0.3 to 0.6 bar, backwashing is due according to Steinbach; Hayward cites 0.7 bar above the starting value. Before every change of the valve position, the pump goes off; both manufacturers insist on that.
The water then runs backward through the sand and flushes the dirt into the waste line until it runs clear in the sight glass, with Steinbach after no more than two minutes. This is followed by rinsing for 20 to 30 seconds so that no loosened dirt gets back into the pool. Steinbach estimates 200 to 1,100 liters of water per backwash, which then has to be topped up. So before buying, plan where this surge will drain.
There is one thing no sand filter can do. According to the Steinbach manual, it does not help against algae; that remains the job of water care. Nor does it clean the floor; that is what pool robots are for.
What the pump needs to be able to do
Self-priming or not determines where it can be set up. According to the data sheet, the Intex units are not self-priming; the Steinbach Comfort models are. Steinbach and Bestway require the pump to stand below the water level, and Steinbach additionally requires it to be no more than three meters from the pool on a solid, level slab. Running dry damages the motor.
Then there is noise. Steinbach states a sound pressure level of 70 dB(A) for the Comfort 75 and Active Balls 75, and 85 dB(A) for the Intex units. Fifteen decibels more is a clearly audible difference, especially when the pump runs next to the patio in the evening. Check the connection, too. The Steinbach units fit hoses of 32 and 38 millimeters; the Intex units are designed for 38 millimeters.
Seven units and their key specs
| Model | Circulation rate according to manufacturer | Filter medium | Pools up to | Best for |
|---|---|---|---|---|
| Steinbach Comfort 75 | 7,800 l/h (pump 9,400 l/h) | 25 kg sand or 700 g filter balls | 40,000 l | Frame and steel-wall pools with 20 to 35 m³ |
| Steinbach Active Balls 75 | 6,500 l/h (pump 8,500 l/h) | filter balls only, 1,150 g | 33,000 l | those who don’t want to haul sand or backwash |
| Bestway Flowclear 58515 | 3,028 l/h | 8.5 kg sand or filter balls | 18,100 l | small frame pools up to about 15 m³ |
| Bestway Flowclear 58499 | 8,327 l/h | 20 kg sand or filter balls | 54,500 l | medium to large above-ground pools |
| Intex Krystal Clear 26644 | 3,700 l/h (pump 4,500 l/h) | 12 kg sand or 336 g filter balls | 18,000 l | small Intex pools with 38 mm connection |
| Intex Krystal Clear 26648 | 8,000 l/h (pump 10,500 l/h) | 35 kg sand or 1,000 g filter balls | 57,500 l | large Intex pools from 30 m³ |
| Hayward S166T (filter unit S166T8103) | 6 m³/h (rated value of the filter) | 50 kg sand | not stated | permanently installed pools with plumbing |
Steinbach Comfort 75
Steinbach states both performance figures openly and supplies a self-priming pump with pre-filter, a 7-way valve and a pressure gauge. The tank measures 415 millimeters and holds 25 kilograms of sand, or alternatively filter balls or filter wool. With a power draw of 550 watts, it is oversized for an 18-cubic-meter pool. From about 20 cubic meters, it fits.
Steinbach Active Balls 75
Same tank, different idea: according to the manufacturer, this unit is intended exclusively for filter balls, and 1,150 grams are included. There is no backwashing; instead, the balls are washed by hand. If you use flocculants, avoid this unit.
Bestway Flowclear 58515
According to the manufacturer, the smallest Bestway unit moves 3,028 liters per hour and takes about 8.5 kilograms of sand. A pre-filter basket and a chlorine dispenser are included. By our calculation, that is enough for pools up to about 15 cubic meters; we consider the stated 18,100 liters a tight fit.
Bestway Flowclear 58499
With 8,327 liters per hour and 20 kilograms of sand, it plays in the same performance class as the Comfort 75. Bestway states pools up to 54,500 liters. If, as with the Comfort 75, you assume just over 80 percent for the filled tank, that leaves just under 7 cubic meters per hour. We would plan on it for up to about 35 cubic meters.
Intex Krystal Clear 26644
A compact unit with a 254-millimeter tank, 12 kilograms of sand and a ground-fault circuit interrupter in the plug. The pump is not self-priming and, according to the data sheet, comparatively loud at 85 dB(A). Suits small pools with a 38-millimeter connection.
Intex Krystal Clear 26648
The large Intex unit with a 360-millimeter tank, 35 kilograms of sand and a timer. The pool rating of 57,500 liters can only be achieved with long run times. For 30 to 40 cubic meters, it makes sense, provided the location is far enough from the patio.
Hayward S166T filter unit
This filter is built for pools with fixed plumbing. According to the manual, the 16-inch S166T filter has a filter area of 0.13 square meters, is designed for 6 cubic meters per hour and needs 50 kilograms of sand. That is twice as much sand as in the Comfort 75 at a similar tank diameter, so the sand bed is considerably deeper. According to the manual, the top of the filter may be no more than 1.5 meters above the water level. Which pump comes in the set is stated in the respective product description.
With permanent installations, the pump is often chosen separately. Speck makes such a pump, the Badu Magic II, in four sizes from 0.35 to 0.72 kilowatts of power draw; according to the data sheet, the largest moves 11 cubic meters per hour. It belongs with a filter tank and suitable plumbing, not on an above-ground pool with 32 mm hoses.
How we would decide
- Above-ground pool up to about 15 m³: Bestway Flowclear 58515 or Intex 26644. With the Intex, factor in the noise.
- 20 to 35 m³: Steinbach Comfort 75, because circulation and pump rates are stated openly and the pump is self-priming.
- No sand, no backwash water: Steinbach Active Balls 75, provided you do without flocculants.
- Large pools over 35 m³: Intex 26648 with longer run times; we only plan on the Bestway 58499 for up to about 35 m³.
- Permanent pool with plumbing: Hayward S166T, with a Speck pump if needed.
If you want to use the water earlier in spring, you will find suitable heaters in our guide to pool heaters (in German).
If the pH value drifts, an accurate measurement helps; devices and calibration are explained in our guide to the pH meter (in German).
Before buying the filter, it is worth looking at the pool itself: in our review of the Bestway Power Steel pool, the frame and ladder rusted after a short time.
Frequently asked questions
Which sand filter suits my pool?
Rule of thumb: pool volume in cubic meters divided by six gives the circulation rate needed per hour if the pump runs for twelve hours. A round pool with about 18 cubic meters therefore needs around 3 cubic meters per hour. Calculate with the water level, not the wall height.
What is the difference between pump rate and circulation rate?
The pump rate applies to free flow, the circulation rate to a filled tank, because the sand slows the water down. For the Steinbach Comfort 75, that is 9,400 and 7,800 liters per hour. The smaller value always counts for the calculation. If a manufacturer gives only one flow figure, plan with a deduction.
Is filter glass better than sand?
Steinbach describes filter glass as filtering slightly finer, needing less water for backwashing and lasting about four years, roughly twice as long as sand. In return, it costs more to buy. If you have to replace the media anyway and want less backwash water, glass is a good choice.
When do I need to backwash the sand filter?
Note the pressure on the gauge after a fresh backwash. If it rises by 0.3 to 0.6 bar, backwashing is due according to Steinbach; Hayward cites 0.7 bar. Switch off the pump first. Steinbach estimates 200 to 1,100 liters of water per backwash, so plan for the drainage.
What speaks for filter balls instead of sand?
According to Steinbach, 700 grams of filter balls replace 25 kilograms of sand, which saves the hauling. They must not be backwashed; they are washed by hand at least once a season. Flocculants are off-limits because they make the balls clump. If you like to use flocculant, stick with sand.
How loud is a sand filter?
Steinbach states a sound pressure level of 70 dB(A) for the Comfort 75 and Active Balls 75, and 85 dB(A) for the Intex units. Fifteen decibels more is clearly audible, especially when the pump runs next to the patio in the evening. Plan the location accordingly.
Sources
- Steinbach: Operating manual, Comfort 50 / Comfort 75 filter system (2026, German)
- Steinbach: Operating manual, Active Balls 50 / 75 filter system (German)
- Steinbach: Comfort 75 filter system, technical data (German)
- Steinbach: Active Balls 75 filter system, technical data (German)
- Steinbach (Intex distributor): Krystal Clear sand filter 26644 (German)
- Steinbach (Intex distributor): Krystal Clear sand filter 26648 (German)
- Steinbach: Filter media at a glance (German)
- Steinbach: Sand filters for proper pool care (German)
- Bestway: Flowclear 58515
- Bestway: Flowclear 58499
- Intex: 12-inch sand filter, fill quantities for sand and glass
- Hayward: Manual for top-mount sand filters (S144T to S244T)
- Speck: Badu Magic II, technical data
Where to buy
- Steinbach Comfort 75Check price at Amazon.deAvailable in Germany: Amazon.de
- Steinbach Active Balls 75Check price at Amazon.deAvailable in Germany: Amazon.de
- Bestway Flowclear 58515Check price at Amazon.deAvailable in Germany: Amazon.de
- Bestway Flowclear 58499Check price at Amazon.deAvailable in Germany: Amazon.de
- Intex Krystal Clear 26644Check price at Amazon.deAvailable in Germany: Amazon.de
- Intex Krystal Clear 26648Check price at Amazon.deAvailable in Germany: Amazon.de
- Hayward Filtereinheit S166T8103Check price at Amazon.deAvailable in Germany: Amazon.de
- Speck Badu Magic II/11Check price at Amazon.deAvailable in Germany: Amazon.de
