Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,734 guides and reviews in German How we test
handgetestet
This page in 6 more languages

DeutschNederlandsFrançaisItalianoEspañolPolski

Buying a Bathroom Faucet 2026: Height, Low Pressure, Cold Start

Buying a bathroom sink faucet: which height suits a vessel sink, when you need a low-pressure model, and what cold start and 5 l/min really deliver.

handgetestet editorial team · Updated November 17, 2026
Contents15 sections

This guide was first published in German on handgetestet.de.

Most bad buys at the bathroom sink have nothing to do with design. The faucet is too low for the vessel sink, or it is connected to a small under-sink water heater in the guest bathroom that it was never built for. For a standard drop-in sink with hot water from the supply line, we consider a single-lever mixer about 110 mm high with cold start and a flow limiter the most sensible choice, for example the hansgrohe Talis E 110 CoolStart. Everything else depends on the sink and the hot water source.

How tall does the faucet need to be for my sink?

Measure first. hansgrohe calls the free space between spout and basin the „ComfortZone,“ and the number in the product name stands for this space in millimeters. A Talis E 110 therefore leaves considerably more room for brushing your teeth than a Focus 70, which according to the manufacturer is intended for small hand-wash basins in guest bathrooms.

With a vessel sink, the calculation changes completely. The bowl sits on top of the countertop, so a standard faucet often ends barely above the rim of the basin. For this, there are tall versions such as the Talis E 240 with a spout height of 234 mm. In that case, also check the spout reach. On the 240 it is 183 mm, on the 110 only 112 mm. A large, deep basin with too short a reach means you end up washing your hands at the back edge of the sink.

Does every faucet work with my small water heater under the sink?

No. This is where the mix-ups with the most serious consequences happen. Unpressurized under-sink water heaters, often found in guest bathrooms, need a low-pressure faucet. According to hansgrohe, the outlet of these mixers stays permanently open: when you open the tap, cold water flows into the water heater and pushes the warm water up. While heating up, the water expands and drips from the spout. That is intended, not a defect. A standard faucet seals tightly, and according to the manufacturer, the open water heater can be damaged.

You can recognize the right faucet by the label „low pressure“ or „for open water heaters.“ The installation instructions for the Focus 70 mention another detail for very small units: on a 5-liter water heater, the mixer must not deliver more than 5 l/min; if necessary, the flow is throttled at the angle valve. According to hansgrohe, the Talis E is suitable for tankless water heaters. Whether your unit works as an open or pressure-resistant system is stated in its manual.

What do flow limiters and cold start really deliver?

At the bathroom sink, the amounts are small, but they add up every day. All mixers in our table have flow regulation from the factory. hansgrohe states a maximum of 5 l/min at 3 bar for the Talis E, and GROHE also 5 l/min for the current Eurosmart. According to the manufacturer, the lever of the Eurosmart can be limited even further, down to about 2.5 l/min depending on the line pressure.

Cold start is more interesting. A conventional mixer already draws hot water in the middle position, even though nothing warm ever reaches the spout during a quick hand wash. With CoolStart, according to hansgrohe, hot water only flows when you actively move the lever to the side. GROHE calls this „Mittelstellung kalt“ (cold in the middle position), HANSA „Kaltstarttechnik“ (cold start technology). For a family bathroom with a gas boiler or tankless water heater, we would no longer do without it.

A note from the hansgrohe manual for tankless water heaters: if the unit does not ignite reliably at 5 l/min, the EcoSmart limiter behind the aerator may be removed. In this case, the manufacturer advises against a hot water lock.

Pop-up rod or push-open?

A matter of taste with a practical core. The pop-up rod behind the lever is tried and tested and can be operated without wet fingers. Push-open, as on the Eurosmart in this version, looks tidier, but you press directly on the stopper in the basin. Whether the drain assembly fits the drain of your sink is something the maker of the ceramic basin can tell you. Ask beforehand.

Chrome, matte black, and what about nickel?

For care, hansgrohe applies the same rules to chrome and all special finishes: a soft cotton cloth, no abrasive cleaners, no microfiber cloths. Apply cleaners based on citric acid to the cloth, never spray them directly onto the faucet, and then wipe with clear water. Residues of soap, aftershave or hair dye should be removed immediately.

On nickel, the German Environment Agency (Umweltbundesamt, UBA) is clear. Chrome-plated faucets can release nickel into drinking water, especially in the first 0.2 liters after water has stood for a long time. The limit value is 20 µg/l, and so far nickel release is not a test criterion in certification. The UBA’s advice is simple: let the water run until it comes out cooler, and only then drink it. In the agency’s assessment, a new faucet does not reliably solve the problem. In its manual, hansgrohe likewise recommends not using the first half liter in the morning as drinking water.

Can I install it myself?

With some skill, yes, on a pressurized supply. The hansgrohe instructions require pipes and faucet to be installed, flushed and tested in accordance with the applicable standards. An operating pressure of 1 to 5 bar is recommended. Silicone containing acetic acid is off-limits. Nothing else may be mounted on the drain assembly, not even a pedestal. For low-pressure setups with a water heater, we would hire a plumber. Water heater and faucet have to work together precisely there.

Six bathroom faucets we consider worthwhile

ModelHeight / reachFlow rate according to manufacturerDrainBest for
hansgrohe Talis E 110 CoolStart (71714000)Spout 104 mm / 112 mmmax. 5 l/min at 3 barwithout drain assemblyDrop-in sinks with central hot water
hansgrohe Talis E 240 (71716000)Spout 234 mm / 183 mmmax. 5 l/min at 3 barPop-up rodVessel sinks
GROHE Eurosmart S-Size Push-Open (23922003)S-Sizemax. 5 l/min at 3 barPush-openChrome or matte black, clean look
HANSA Polo (51402293)Reach 103 mm according to retailer informationconstant regulation, 6 l/min according to retailer informationPop-up rodSolid mixer for bathroom and guest bathroom with a pressurized line
hansgrohe Focus 70 low pressure (31132000)Spout 53 mm / 101 mmmax. 5 l/min, from 0.2 barPop-up rodGuest bathroom with an unpressurized under-sink water heater
GROHE Eurosmart Cosmopolitan low pressure (32955000)S-SizeAdjustable flow limiterPop-up rodOpen water heater, alternative to the Focus

hansgrohe Talis E 110 CoolStart

Our favorite for the standard bathroom. According to hansgrohe, 104 mm spout height, 112 mm reach, limiter set to 5 l/min, cold start. We list version 71714000 without a drain assembly here, because the existing drain assembly in the basin can usually be reused when replacing the faucet. Version 71713000 with a metal pop-up rod is harder to find in stores. The faucet is approved for tankless water heaters. Besides chrome, the series is available in other colors.

hansgrohe Talis E 240

The tall sister for vessel sinks. A spout height of 234 mm and a reach of 183 mm extend over deeper bowls too.

GROHE Eurosmart S-Size with push-open

Smooth body without a pop-up rod, 28 mm SilkMove cartridge, temperature limiter and adjustable flow limiter. GROHE offers it in chrome and matte black. If you want cold start, GROHE has a separate version with „Mittelstellung kalt.“

HANSA Polo

A no-fuss single-lever mixer with pop-up rod, temperature limiter and a hot water lock that can be retrofitted. According to HANSA, the aerator keeps the flow constant regardless of pressure. Only the specifically labeled energy-saving version has cold start.

hansgrohe Focus 70 for open water heaters

Built for the small water heater in the guest bathroom: low-pressure technology from 0.2 bar, 5 l/min, pop-up rod. With a spout height of 53 mm, it suits small hand-wash basins; for large basins, it is too low.

GROHE Eurosmart Cosmopolitan low pressure

GROHE’s answer to the same situation. According to the manufacturer, for open water heaters, with a 35 mm cartridge, adjustable flow limiter and pop-up drain.

Which faucet suits which bathroom?

  • Drop-in sink, hot water from the heating system or a tankless water heater: hansgrohe Talis E 110 CoolStart.
  • Vessel sink: Talis E 240; measure basin height and depth first.
  • Dark look without a pop-up rod: GROHE Eurosmart S-Size Push-Open in matte black.
  • Guest bathroom with an under-sink water heater: Focus 70 low pressure or Eurosmart Cosmopolitan low pressure, never a standard mixer.

If you are renovating the kitchen at the same time, you will find the differences between kitchen sink mixers in our guide to kitchen faucets. If there are a water heater and hoses under the sink, you will find warning devices for emergencies in our guide to water leak detectors.

Frequently asked questions

How tall does a bathroom faucet need to be?

That depends on the sink. hansgrohe calls the free space between spout and basin the ComfortZone, and the number in the product name stands for this space in millimeters. With a vessel sink, a standard faucet often ends barely above the rim; for this, there are tall versions such as the Talis E 240 with a spout height of 234 mm. Also check the spout reach.

Which faucet works with a small water heater under the sink?

Unpressurized under-sink water heaters need a low-pressure faucet, recognizable by the label low pressure or for open water heaters. With these, the outlet stays permanently open, and water drips out while heating up; that is intended. A standard faucet seals tightly, and according to hansgrohe, the open water heater can be damaged.

What does cold start do on a bathroom faucet?

A conventional mixer already draws hot water in the middle position, even though nothing warm ever reaches the spout during a quick hand wash. With cold start, hot water only flows when you actively move the lever to the side. hansgrohe calls this CoolStart, GROHE "Mittelstellung kalt" (cold in the middle position), HANSA "Kaltstarttechnik" (cold start technology).

Do chrome-plated faucets release nickel into drinking water?

According to the German Environment Agency (Umweltbundesamt), this can happen, especially in the first 0.2 liters after water has stood for a long time. So far, nickel release is not a test criterion in certification. The agency advises letting the water run until it comes out cooler and only then drinking it. hansgrohe recommends not using the first half liter in the morning as drinking water.

How do you clean a bathroom faucet properly?

For chrome and all special finishes, hansgrohe recommends a soft cotton cloth, no abrasive cleaners and no microfiber cloths. Apply cleaners based on citric acid to the cloth, never directly onto the faucet, and then wipe with clear water. Residues of soap, aftershave or hair dye should be removed immediately.

Can I install a bathroom faucet myself?

With some skill, yes, on a pressurized supply. According to hansgrohe, pipes and faucet must be installed, flushed and tested in accordance with the applicable standards, and an operating pressure of 1 to 5 bar is recommended. Silicone containing acetic acid is off-limits. For low-pressure setups with a water heater, a plumber should do the job, because water heater and faucet have to work together precisely.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.