Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,734 guides and reviews in German How we test
handgetestet

Deutsch

Buying Bar Clamps 2026: One-Handed, All-Steel, Case Clamps

Buying bar clamps: understanding clamping range, throat depth and clamping force, choosing between all-steel and one-handed clamps, and when you need case clamps for furniture.

handgetestet editorial team · Updated November 17, 2026
Contents13 sections

This guide was first published in German on handgetestet.de.

A glue joint between two beech boards does not forgive a weak clamp. If you are putting together your first set, you are therefore better off buying two types than ten identical ones. Our suggestion for the basic kit: a few all-steel bar clamps such as the Bessey GZ30-12-2K for force, plus one-handed clamps for everything that needs to happen quickly. Case clamps only come in once you glue up cabinets or tabletops.

Three measurements printed on every clamp

Bessey explains the measurements like this: the clamping range runs from the upper to the lower clamping pad and is therefore the longest workpiece that will fit. The throat depth is measured from the inside of the rail to the center of the spindle. It decides how far from the edge the clamp can still apply pressure. The third measurement is the rail cross-section, meaning the width times the thickness of the rail. The larger it is, the more clamping force the clamp can handle.

An everyday example. You are gluing a strip onto a shelf board 10 cm in from the edge. A clamp with 60 mm of throat depth presses into thin air next to it. With 120 mm, the clamping pad sits right over the strip.

That leaves clamping force. Bessey states it in newtons, while Wolfcraft, Irwin and Piher use kilograms. One kilogram corresponds to roughly 9.81 newtons. The 250 kg of a Wolfcraft PRO MAX are therefore just under 2,450 N, and the 6,000 N of a Bessey GZ a good 610 kg. For the models below, there is roughly a factor of two to three between a one-handed clamp and a bar clamp.

Malleable cast iron, all-steel or plastic housing?

Bessey offers both classic designs. The manufacturer describes malleable cast iron clamps as rigid and torsion-resistant, with very high clamping force, intended mainly for gluing. All-steel clamps are heat-treated and give slightly under load. As a result, they absorb vibrations, which is why Bessey recommends them for metalwork, welding, and sawing and sanding wood.

One-handed clamps work differently. Instead of turning a spindle, you squeeze a pump handle, and the housing is usually made of glass-fiber-reinforced plastic. That is quick, with just one hand, while the other aligns the workpiece. Their force is not always enough, however, for the sustained pressure a wide glue joint needs. That is why we would never buy one-handed clamps exclusively.

Seven clamps and their key figures

ModelDesignClamping range / throat depthClamping force according to the manufacturerBest for
Bessey GZ30-12-2KAll-steel, spindle300 / 120 mmup to 6,000 NGluing, metal, welding
Bessey EZS30-8One-handed clamp300 / 80 mmup to 2,000 NQuick fixing, spreading
Irwin Quick-Grip Heavy-Duty 300 mm (10505943)One-handed clamp, steel beam300 / 92 mmup to 272 kgAssembly, spreading
wolfcraft PRO MAX 450 mm, 2er-Set (8662060)One-handed clamp450 / 110 mm250 kgFurniture making, deep workpieces
Piher Maxi Quick-300, 30 cm (52692)One-handed clamp30 cm300 kgWood shop, frequent repositioning
Bessey REVO KRE60-2KCase clamp600 / 95 mmup to 8,000 NCabinets, frames, panel glue-ups
Kreg Classic Face Clamp 51 mm (KHC-MICRO)Face clampmaterial up to 57 mm / 51 mmnot specifiedPocket-hole joints

Bessey GZ30-12-2K

This all-steel bar clamp with a two-component handle is our recommendation for the foundation of your set. Bessey states up to 6,000 N, a clamping range of 300 mm, a throat depth of 120 mm and a weight of 1.46 kg. A redesigned rail profile is said to deliver 20 percent more clamping force per turn of the spindle, and the clamping pads can be swapped without tools.

Bessey EZS30-8

According to Bessey, this one-handed clamp applies up to 2,000 N, has a throat depth of 80 mm and weighs 0.83 kg. A release mechanism on the upper part turns it into a spreader without tools, and it then pushes apart from 170 to 510 mm. The handle sits behind the rail. For holding parts in place, marking out and drilling, that does the job well.

Irwin Quick-Grip Heavy-Duty 300 mm

Irwin builds the rail as a heat-treated I-beam made of carbon steel with a black oxide finish, which according to the manufacturer bends less. The specifications are up to 272 kg of sustained clamping force, a throat depth of 92 mm and a spreading range of 235 to 530 mm. A quick-change button releases the jaws. A practical touch is the stand foot, which lets the clamp stand upright.

wolfcraft PRO MAX 450 mm

According to the catalog, this is the strongest one-handed clamp in the wolfcraft range: 250 kg, a throat depth of 110 mm, a spreading range of 220 to 710 mm and 1.35 kg per clamp. The hardened steel rail has a bone-shaped profile, and the rubberized jaws have a V-groove for round stock. It is released with a lever. According to its press release, Wolfcraft gives a ten-year warranty. Set 8662060 contains two clamps, and you need at least a pair for a glue joint anyway.

Piher Maxi Quick-300

The Spanish manufacturer Piher states up to 300 kg of pressure for the Maxi Quick-300, generated by the patented Easy-Grip system. The heads are made of glass-fiber nylon, and the rail of hardened steel measuring 20 × 5 mm. It releases in two stages and reverses with a single click. The sliding shoes are extra long and slip-resistant.

Bessey REVO KRE60-2K

Case clamps have large, parallel clamping faces so that a cabinet carcass stays square while the glue sets. Bessey states up to 8,000 N for the REVO KRE. The housing is metal-reinforced, and the sliding arm is doubly secured against slipping. The handle has a hex socket for a wrench, with a maximum of 17 Nm according to the manufacturer. The 600 version opens up to 600 mm, and for tabletops, lengths of up to 2,500 mm are available.

Kreg Classic Face Clamp 51 mm

Not a clamp in the strict sense, more of a locking plier. It holds two boards flush while the pocket-hole screws go in, and the large pad belongs on the show face. Kreg states a throat depth of 51 mm and material up to 57 mm thick, adjusted via a screw. More on this in the pocket-hole jig guide (in German).

Which clamp for which job?

  • Gluing boards and frames: four Bessey GZ30-12-2K, plus case clamps such as the REVO KRE for cabinets.
  • Welding and metal: all-steel, because the clamp gives a little. Bessey explicitly names this design for welding work.
  • Assembly, holding parts in place, drilling: two one-handed clamps, depending on the throat depth you want, the Bessey EZS (80 mm), the Irwin (92 mm) or the wolfcraft PRO MAX (110 mm).
  • Furniture with pocket-hole joints: the Kreg face clamp, supplemented by a one-handed clamp.

Clamps need a base that does not give way. You will find a sturdy top with an overhang at the edge in the workbench guide (in German). For parts that have to be held firmly all around while filing or sawing, a bench vise is the better choice than any clamp.

When the clamp slips

It is usually the rail. Bessey explains that a bar clamp holds through friction and binding between the rail and the sliding arm. Grease, oil and dried glue therefore have to come off, and wax and silicone-based release agents immediately. The manufacturer roughens bare, shiny spots on an all-steel rail with 100-grit abrasive cloth on both sides. The spindle and the clamping pad joint, by contrast, get a drop of oil now and then. Sounds contradictory. It is not: oil belongs on the thread, never on the rail.

One last tip for buying: pay attention to the complete part number. At Bessey, “GZ30” covers several throat depths and handles, and at wolfcraft, the two-pack carries a different number than the single clamp.

Frequently asked questions

What do clamping range and throat depth mean on a bar clamp?

The clamping range runs from the upper to the lower clamping pad and determines the longest workpiece. The throat depth is measured from the rail to the center of the spindle and decides how far from the edge the clamp can still apply pressure. A strip 10 cm in from the edge calls for about 120 mm instead of 60 mm.

How do you convert clamping force from kilograms to newtons?

One kilogram corresponds to roughly 9.81 newtons. The 250 kg of a wolfcraft PRO MAX are therefore just under 2,450 N, and the 6,000 N of a Bessey GZ a good 610 kg. Bessey states newtons, while Wolfcraft, Irwin and Piher state kilograms. Between a one-handed clamp and a bar clamp, there is roughly a factor of two to three.

What is the difference between malleable cast iron and all-steel?

Bessey describes malleable cast iron clamps as rigid and torsion-resistant with very high clamping force, intended mainly for gluing. All-steel clamps are heat-treated and give slightly under load. As a result, they absorb vibrations, which is why Bessey recommends them for metalwork, welding, and sawing and sanding wood.

Are one-handed clamps enough for gluing?

Not always. They work with a pump handle instead of a spindle and can be operated with one hand while the other aligns the workpiece. Their force is not always enough, however, for the sustained pressure a wide glue joint needs. This guide therefore considers it a mistake to buy only one-handed clamps.

When do you need a case clamp?

When gluing cabinets, frames and panels. Case clamps have large, parallel clamping faces so that a cabinet carcass stays square. Bessey states up to 8,000 N for the REVO KRE, and the 600 version opens up to 600 mm. For tabletops, lengths of up to 2,500 mm are available.

What should you do if the clamp slips?

It is usually the rail, because a bar clamp holds through friction between the rail and the sliding arm. Grease, oil, dried glue, wax and release agents have to come off. Bessey roughens shiny spots on all-steel rails with 100-grit abrasive cloth. Oil belongs on the thread, never on the rail.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.