Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,734 guides and reviews in German How we test
handgetestet

Deutsch

Homematic IP Shading Set: Retrofitting Roller Shutters

Retrofitting a Homematic IP shading set: neutral wire, obstacle detection, venetian blinds and which set suits how many roller shutters.

handgetestet editorial team · Updated November 17, 2026
Four white Homematic IP roller shutter actuators for branded switch series and an Access Point 2 on a light backgroundImage: ELV (Pressebild)
Contents14 sections

This guide was first published in German on handgetestet.de.

Four electric roller shutters with wall switches? Then the Homematic IP Set Beschattung 4 Rollladenaktoren (shading set with four roller shutter actuators) is the right fit: the hub and actuators come in one box, and your existing switch series can stay. Still, do not order it first. The instructions state a condition that does not appear in the retailer’s product descriptions, and for external venetian blinds the set is simply the wrong choice.

Three checks before you order

First, the drive. According to the user manual, the actuators control anything that has an electric tubular motor and two wires, one for raising and one for lowering. If the window still has a pull strap, an actuator has nothing to switch. For that case, there is our article on smart roller shutter control (in German) with strap winders, and if you want to get rid of the strap entirely, read on in our guide to the roller shutter motor (in German).

Next, the wall box. None of the actuators works without a neutral wire; every data sheet says so. There is hardly any way around it, because Bosch and Eve require one too. Older installations do not always have one, and only someone trained to do so should check. eQ-3 requires a qualified electrician for all work on the 230-volt mains.

Now for the inconvenient part. The instructions for the HmIP-BROLL-2, HmIP-FROLL and HmIP-BBL-2 only permit operation with tubular motors that have built-in obstacle detection. The shop, on the other hand, says „all common tubular motors“; ELV names Lifteo, Selve SEL Plus and Schellenberg Standard and Plus as tested in-house. So check the type and features of your motor before you spend any money. If it does not match, a motor replacement may be due, and the math looks different. The end positions must also be set properly. The load limit is 500 VA or 2.2 amps per actuator.

Branded switch series or flush-mounted?

The shading sets contain the HmIP-BROLL-2. It replaces the old switch, measures 71 × 71 × 37 mm and then carries your frame and rocker. In between sits an adapter that, according to the scope of delivery, is not included, so you need one extra per window. Read the adapter list beforehand. With many series it works without modification, with some it does not: for Jung LS 990 the rocker mounts have to be shortened, and for Gira Trend the frame cutout is milled larger. Hardly anyone enjoys doing that to a designer frame.

The HmIP-FROLL works invisibly. It measures 54 × 33 × 41 mm and connects a normal push button to its own terminals, so no adapters are needed. In a surface-mounted box, it can also go in the garage or under the roof overhang. eQ-3 does not state a minimum depth for the wall box. Bosch requires 50 mm for its insert, which is only 22 mm deep, so expect to need a deep box here. The automatic calibration run is only available on the BROLL and the BBL; on the FROLL, the travel times are determined manually.

On price, the flush-mounted actuator comes out ahead. The five-actuator set with it costs about a quarter less per window at ELV (German retailer) than the branded-switch set of the same size (as of November 2026). More important for the math: compared with an Access Point 2 plus individual actuators, a set only saves about five to six percent. For three roller shutters, the four-actuator set would therefore be a waste. The starter set with two actuators plus one individual actuator works out cheaper.

And the standby power? Let us take a house with seven roller shutters and, to be cautious, assume the full value of 1 watt for the Access Point 2. 7 × 0.2 watts plus 1 watt makes 2.4 watts, so over 8,760 hours roughly 21 kilowatt hours a year. That is negligible.

Venetian blinds and external venetian blinds need a different actuator

According to eQ-3, roller shutter actuators only control the height of the shutter. Only the blind actuator adjusts slats, and none of the shading sets contains it. If you have external venetian blinds, buy the Access Point 2 and one HmIP-BBL-2 per window separately. A set brings nothing here. On the BBL-2, the slats are adjusted with a long press of the button, and according to ELV the switch series needs a one-piece rocker. Bosch solves it differently: there, the same insert handles both height and tilt, and you choose the operating mode when pairing.

What is missing from the box

Time profiles and movements based on sunrise and sunset work with the set right away. Up no earlier than 6:30 a.m., down at dusk in the evening: that works. Everything else requires accessories, and that quickly turns the set into a project:

  • Lockout protection at the patio door: a door and window contact (in German). By default, it only stops time and sun profiles. If someone presses the button, the roller shutter still goes down.
  • Heat protection: a temperature sensor in the room, such as a wall thermostat. An outdoor sensor is not enough.
  • Escape function: a Homematic IP smoke alarm.
  • Storm protection: it works without a sensor using online weather data, which according to eQ-3 can, however, differ from conditions on site.

One limitation applies to all of these protective functions. They are checked in the cloud and need an active internet connection. Time profiles, on the other hand, are stored in the devices and keep running without a connection. If you want it to work differently, you will find the differences in our comparison of Homematic hubs (in German).

Sets and alternatives side by side

ModelContentsRequirementBest for
Homematic IP Set Beschattung 4 RollladenaktorenAccess Point 2, 4 × HmIP-BROLL-2Neutral wire, adapter per switch seriesfour roller shutters, switches stay
Homematic IP Starter Set Rollladensteuerung HmIP-SK29Access Point 2, 2 × HmIP-BROLL-2, 2 push-button rockers, adapter, frameNeutral wiretwo to three roller shutters
Homematic IP Set Rollladen 5x Rollladenaktor UnterputzAccess Point 2, 5 × HmIP-FROLLNeutral wire, room in the wall boxpush buttons stay, low cost per window
Homematic IP Set Wetterschutz2 × HmIP-BROLL-2, Weather Sensor Plus, no hubexisting hubexisting system with an awning
Homematic IP blind actuator HmIP-BBL-21 actuator with slat controlHub, neutral wire, adapterexternal venetian blinds and outdoor blinds
Bosch Smart Home Licht-/Rollladensteuerung IIInsert for height and tiltSmart Home Controller, wall box from 50 mmBosch households
Eve Shutter SwitchSwitch with frame, Thread, MatterNeutral wire, Thread border routerApple and Matter households

Homematic IP Set Beschattung 4 Rollladenaktoren

This is where we start if nothing speaks against it, because the switch series is kept and the rocker still works by hand, even when the internet is down. The same equipment is available with five to eight actuators. According to ELV, the Access Point 2 manages up to 120 devices. Downsides: adapters cost extra, and per window the sets are more expensive than the flush-mounted version. Incidentally, the description in the shop mentions five actuators, while the scope of delivery lists four. The scope of delivery is what counts.

Homematic IP Starter Set Rollladensteuerung HmIP-SK29

The least expensive way in with the current hub (roller shutter control starter set). Push-button rockers with the adapter already fitted and replacement frames are included. That spares you the search for adapters, but only looks inconspicuous next to a white series. We advise against the older Starter Set Beschattung HmIP-SK20, which still contains the first-generation Access Point.

Homematic IP Set Rollladen 5x Rollladenaktor Unterputz

The most economical solution per window (set with five flush-mounted roller shutter actuators), and independent of the switch series as well. It stands or falls with the room in the wall box. The electrician should check this at one window before you buy.

Homematic IP Set Wetterschutz

Despite the name (weather protection set), this is not a starter set, because there is no hub. The Weather Sensor Plus measures wind, rain, brightness and temperature and sits on a 1.58-meter mast. For roller shutters alone, we consider it overkill. With an awning, things look different; more on that in our guide to smart awning control (in German).

Homematic IP blind actuator HmIP-BBL-2

Technically the sibling of the BROLL-2, with the same requirements for neutral wire and motor. What matters in storms: depending on their wind resistance class, external venetian blinds have to retract upward, while roller shutters may go down in wind. You set the direction of travel in the app.

Bosch Smart Home Licht-/Rollladensteuerung II

The flat insert (light/roller shutter control) sits behind the existing switch without an adapter and can also switch lights. It only works with the Bosch Smart Home Controller. So it makes sense where one is already installed. Bosch states a wall box depth of 50 mm as the minimum and recommends 60 mm.

Eve Shutter Switch

A complete switch instead of an insert. According to Eve, existing switch plates do not fit, and the frame has to follow the 55 mm standard. You also need a Thread border router. In return, you are not tied to a single manufacturer’s hub.

How we would decide

  • Four to eight roller shutters, switch series should stay: shading set in the matching size.
  • Two or three roller shutters: Starter Set SK29, plus one individual actuator for three.
  • Simple push buttons and deep wall boxes: set with flush-mounted actuators.
  • External venetian blinds: Access Point 2 and HmIP-BBL-2 individually.
  • Motor without obstacle detection: sort out the drive first, then the set.

How an existing radio-controlled awning with WMS technology can be made smart after the fact is shown in our hands-on test of the Warema Cube.

Frequently asked questions

Which roller shutters can be retrofitted with Homematic IP?

According to the user manual, anything with an electric tubular motor and two wires, one for raising and one for lowering. If the window still has a pull strap, an actuator has nothing to switch. The instructions also only allow tubular motors with built-in obstacle detection, so check the type and features beforehand.

Do roller shutter actuators need a neutral wire?

Yes, none of the actuators works without a neutral wire, and Bosch and Eve require one too. Older installations do not always have one. Only someone trained to do so should check; eQ-3 requires a qualified electrician for all work on the 230-volt mains.

What is the difference between the HmIP-BROLL-2 and the HmIP-FROLL?

The BROLL-2 replaces the old switch and carries your frame and rocker; in between sits an adapter specific to the switch series, which is not included. The FROLL works invisibly behind a normal push button and needs no adapter, but it needs room in the wall box. The automatic calibration run is only available on the BROLL.

Can the shading set also control external venetian blinds?

No. According to eQ-3, roller shutter actuators only control the height of the shutter; only the blind actuator adjusts slats, and none of the sets contains it. For external venetian blinds, buy the Access Point 2 and one HmIP-BBL-2 per window separately. According to ELV, the switch series needs a one-piece rocker.

Do the protective functions work without internet?

No. Lockout protection, heat protection, escape function and storm protection are checked in the cloud and need an active internet connection. Time profiles, on the other hand, are stored in the devices and keep running without a connection. The protective functions also require accessories, such as a door and window contact.

Is the set worth it for just three roller shutters?

Hardly. Compared with an Access Point 2 plus individual actuators, a set only saves about five to six percent, and for three roller shutters the four-actuator set would be a waste. The HmIP-SK29 starter set with two actuators plus one individual actuator works out cheaper.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.