Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,734 guides and reviews in German How we test
handgetestet

Deutsch

Buying a Workshop Air Compressor 2026: Buyer’s Guide

Air compressors for the workshop: why free air delivery matters more than intake capacity, oil-free or oil-lubricated, tank, noise and five models.

handgetestet editorial team · Updated November 17, 2026
Scheppach HC51VImage: scheppach (Pressebild)
Contents14 sections

This guide was first published in German on handgetestet.de.

A big number is emblazoned on the box. It is almost always the intake capacity, and it reveals surprisingly little about the air that actually reaches the tool.

For a hobby workshop with a tire inflator, blow gun and occasional painting, we would take an oil-free 50-liter compressor such as the Einhell TE-AC 270/50 Silent Plus, because according to the manufacturer it runs quietly and delivers a decent amount of air at 4 bar. If you need a lot of air in one go, you are better off with an oil-lubricated twin-cylinder unit.

Why does the box show the wrong number?

Because it is the bigger one. A piston compressor draws in air, compresses it and pushes it into the tank, and a good share is lost along the way. The data sheets show how much: Einhell rates the Silent Plus at 270 l/min intake capacity but only 132 l/min output at 4 bar. For the Basic 250-50 W, Metabo states 200 l/min, while the effective figure according to the data sheet is 95 l/min. Roughly speaking, about half of these values remains.

How much air does my tool need?

That is stated in its manual. Compare this value with the air delivery at working pressure, not with the intake capacity. Tire inflators and blow guns need little. It is a different story with spray guns, sanders and impact wrenches. They draw air continuously, and a compressor that is too small then runs nonstop. Loosening wheel nuts with compressed air? Then do the math beforehand, rather than being surprised during the tire change. Which sockets fit the job is covered in the article on socket sets.

Bigger tank, more air?

No. The tank is a buffer, not a motor.

With 50 liters you can paint longer before the motor kicks in, but no more air comes out per minute. A small 5-liter tank is enough for tires and short blow-out jobs and fits in the trunk.

Oil-free or with oil?

Oil-free units need no oil changes and no glance at the sight glass. Oil-lubricated piston compressors are the classic design, but they need maintenance: check the oil level, change the oil. For a spray gun, a filter regulator that separates water and oil mist belongs in between, whatever the design.

How loud is loud?

Only the sound power level LwA is comparable. The sound pressure level LpA depends on the measuring distance, and manufacturers do not measure uniformly. Metabo, Scheppach and Aerotec each state a sound power of 97 dB(A) in their data sheets. For the Silent Plus, Einhell only states the sound pressure. A direct comparison is therefore not possible.

8 or 10 bar?

Most DIY tools get by with 8 bar. 10 bar gives some reserve for tires and pneumatic nailers.

And the garage in winter? For the Basic 250-50 W, Metabo explicitly advertises a pressure switch with a relief valve for good cold starts. So cold is an issue for compressors. If you heat your workspace anyway, you will find options under heating the workshop.

Five compressors with manufacturer data

ModelTank, pressure, designIntake / air delivery according to the manufacturerBest for
Einhell TE-AC 270/50 Silent Plus50 l, 8 bar, oil-free270 l/min / 132 l/min at 4 bar; 54 dB(A) LpAWorkshop at the house, where noise is a problem
Metabo Basic 250-50 W50 l, 8 bar, oil-lubricated200 l/min / 95 l/min effective; 97 dB(A) LwAClassic garage, tires and pneumatic nailers
Scheppach HC51V50 l, 10 bar, oil-free, upright220 l/min / not stated; 97 dB(A) LwALittle floor space
Güde 405/10/5050 l, 10 bar, oil-lubricated, 2 cylinders250 l/min at 0 bar, 210 l/min at 4 bar (air delivery)Painting and sanding with high air demand
Aerotec Airliner 5 GO5 l, 10 bar, oil-free200 l/min / 110 l/minMobile: tires, blowing out, small job sites

Einhell TE-AC 270/50 Silent Plus

Einhell states a sound pressure of 54 dB(A) for this oil-free unit. That sounds more like a conversation than a compressor. At 132 l/min at 4 bar, it delivers noticeably more air than the classic 50-liter entry-level models, according to the data sheet. In return, it weighs 42.6 kg and manages 8 bar at most. In the Einhell online shop it was recently out of stock, but retailers still carry it.

Metabo Basic 250-50 W

An oil-lubricated piston compressor without frills: 50 liters, 8 bar, an effective 95 l/min at 80 percent of maximum pressure. It is loud, at 97 dB(A) sound power. In return, Metabo grants a 10-year warranty against the tank rusting through. It handles tires, blowing out and staplers; for longer painting jobs, the air delivery gets tight.

Scheppach HC51V

Standing upright, the tank saves space; according to the data sheet, the unit needs only 364 by 346 millimeters of floor space. Oil-free, 10 bar, two quick couplers, just under 24 kg. The data sheet gives no air delivery at working pressure; Scheppach only states 220 l/min intake capacity. So calculate conservatively.

Güde 405/10/50

Of the five units, it is the most powerful: two cylinders in a V arrangement, oil lubrication, 2.2 kW motor output. At 4 bar, it delivers around 210 l/min according to the data sheet, which lets it keep going longer on a spray gun and random orbital sander.

According to the retailer’s data sheet, it weighs a good 37 kg. It belongs in a fixed location.

Aerotec Airliner 5 GO

Strictly speaking, not a workshop compressor. More of a portable unit with a 5-liter tank and a weight of 8.5 kg, for which Aerotec states 110 l/min air delivery and 10 bar. It may run lying down or standing up. Tires on the car, trailer and bike, blowing out after washing with the pressure washer, the nailer in the attic: for that, it is enough. Only very small parts can be painted with it.

Which compressor for which job?

For a workshop at the house with mixed jobs, the Einhell TE-AC 270/50 Silent Plus has the most going for it. Quiet, oil-free, good air delivery, just limited to 8 bar. If you mainly inflate tires, blow out and staple in the garage, the Metabo Basic 250-50 W is the right choice; solid technology, but loud and with oil maintenance. If space is tight, the Scheppach HC51V is an option, though you should check its air delivery against your tools. Painting and sanding? Güde 405/10/50, although it is oversized for occasional users. And for on the go and tire pressure, there is the Aerotec Airliner 5 GO.

With accessories, people often save in the wrong place. A tire inflator with a calibrated pressure gauge, a sufficiently thick hose and, for paint, a filter regulator do more than any 13-piece budget kit. Drain the tank regularly, otherwise it rusts from the inside. What a fixed workstation for tools and accessories can look like is shown in the article on workbenches (in German).

Frequently asked questions

What is the difference between intake capacity and free air delivery?

The box almost always shows the intake capacity, but a good share is lost during compression. The Einhell Silent Plus is rated at 270 l/min intake capacity but only 132 l/min output at 4 bar. Roughly speaking, about half remains. What matters is the air delivery at working pressure.

How much air does a pneumatic tool need?

It is stated in the tool's manual, and you compare that value with the air delivery at working pressure. Tire inflators and blow guns need little. Spray guns, sanders and impact wrenches draw air continuously, and a compressor that is too small then runs nonstop.

Does a bigger tank deliver more air?

No, the tank is a buffer, not a motor. With 50 liters you can paint longer before the motor kicks in, but no more air comes out per minute. A small 5-liter tank like the one on the Aerotec Airliner 5 GO is enough for tires and short blow-out jobs.

Oil-free or oil-lubricated compressor?

Oil-free units need no oil changes and no glance at the sight glass. Oil-lubricated piston compressors are the classic design but need maintenance. For a spray gun, a filter regulator that separates water and oil mist belongs in between, whatever the design.

How do you compare the noise of compressors?

Only the sound power level LwA is comparable; the sound pressure level LpA depends on the measuring distance. Metabo, Scheppach and Aerotec each state a sound power of 97 dB(A). For the Silent Plus, Einhell only states a sound pressure of 54 dB(A), so a direct comparison is not possible.

Is 8 bar enough for a home workshop?

Most DIY tools get by with 8 bar. 10 bar gives some reserve for tires and pneumatic nailers, for example with the Scheppach HC51V or Güde 405/10/50. Regardless of pressure: drain the tank regularly, otherwise it rusts from the inside.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.