Contents12 sections
This guide was first published in German on handgetestet.de.
If you pour a river table with a resin meant for coasters, in the worst case you end up with a block that boils in the cup. Casting resin is bought by layer thickness, not by brand. For jewelry, coasters and thin coatings up to about 2 cm, we consider the EPODEX PRO System the sensible choice: long working time, UV protection according to the manufacturer and a clear limit per pour. For tabletops with deep channels, you need a different resin.
Pour depth first, everything else after
Epoxy resin cures through a chemical reaction, and that reaction generates heat. In a thin layer, the heat spreads out. In a thick pour, it builds up. In the technical data sheet for its Trasparente resin, Resin Pro states that large quantities can get hotter than 150 °C and therefore limits a single pour to 250 g and no more than 2 cm. In summer, the manufacturer even advises 1 cm.
That is why manufacturers state a maximum pour depth per pour. It determines the product line:
- up to 1 to 2 cm: jewelry, pendants, coasters, pictures, wood coatings;
- up to 5 cm: lamps, small molds, shallow joints in boards;
- up to 10 cm: river tables and embeddings in tall molds.
A quick calculation helps when shopping. A round coaster 10 cm in diameter and 1 cm high needs about 85 g of resin. A river channel of 120 × 20 cm at a depth of 4 cm, on the other hand, swallows a good ten kilograms. With a resin rated for 2 cm, that would mean at least two pours with waiting time in between, or four in summer heat.
Also pay attention to the mixing ratio. EPODEX and Resin Pro state it by weight, such as 2:1, 100:60 or 4:1. For that, a kitchen scale with a gram display belongs in the workshop. Some kits, by contrast, are mixed 1:1 by volume, which works with measuring cups.
Pot life: the figure applies to a small cup
Pot life tells you how long mixed resin stays fluid enough to pour. It depends on quantity and temperature. Resin Pro measures it at 150 g and 25 °C. With 2 kg in a bucket, the clock runs faster because the mass heats itself up. EPODEX therefore recommends pouring immediately after mixing.
Cold slows things down. Both manufacturers name about 20 °C as the lower limit for the room, the workpiece and the resin; otherwise curing takes longer and thin layers can turn cloudy. If you want to pour in the garage in winter, think about heating for the workshop (in German) first.
Moisture is underestimated. According to EPODEX, freshly poured resin should not come into contact with water for about seven days, otherwise white spots may appear.
What resin and hardener do to your skin
Liquid epoxy resin is not a harmless craft material. BG BAU, the German employers‘ liability insurance association for the construction industry, writes that epoxy resins are highly allergenic and can quickly lead to skin allergies. According to its DGUV Information 201-062, workers develop eczema every year from skin contact with uncured resin, and many then have to change careers. Once acquired, an allergy is permanent.
What the insurance association requires:
- Protective gloves made of nitrile or butyl rubber that are tested for epoxy resin; leather gloves and nitrile-impregnated cotton gloves do not protect.
- Barrier cream is no substitute for gloves.
- Safety goggles when mixing, plus long sleeves and long pants.
- Dab off splashes, then wash with warm water and detergent. Never put solvents on your skin.
How seriously manufacturers take this can be seen in the safety data sheets. The hardener of Resin Pro Trasparente carries the signal word „Danger“; according to the data sheet, it causes severe skin burns and may cause allergic reactions. It recommends nitrile gloves 0.35 mm thick with a breakthrough time of more than 480 minutes. If all you have in the cupboard are wafer-thin gloves, compare that figure with your own pack. The EPODEX hardener is also labeled „Danger.“
There is some good news. According to the DGUV (German Social Accident Insurance), cured epoxy resin does not trigger allergies and is not hazardous waste. So stir leftover resin and hardener together and let them cure instead of throwing them away liquid. Sanding later with a random orbital sander produces fine dust, and then a suitable dust mask is part of the job.
Six casting resins for the workbench and craft corner
| Resin | Max. pour depth per pour | Mixing | Pot life or working time | Best for |
|---|---|---|---|---|
| EPODEX PRO System | 1–2 cm | 2:1 by weight | approx. 60–120 min | Jewelry, coasters, coatings |
| EPODEX ECO System | 1 cm | 2:1 by weight | approx. 60–120 min | Thin layers without sunlight |
| EPODEX PRO MAX System | 10 cm | 2:1 by weight | approx. 8 hrs | River tables, tall molds |
| Resin Pro iCrystal | 1.5 cm | 100:50 by weight | 30 min (150 g, 25 °C) | Clear jewelry, small embeddings |
| Resin Pro Trasparente | 2 cm (max. 250 g) | 100:60 by weight | approx. 50 min (150 g, 25 °C) | Craft projects, repairs |
| Resin Pro EpoxyTable 10 | 10 cm | 4:1 by weight | 24 hrs (125 g, 25 °C) | Tabletops, for the patient |
EPODEX PRO System
For small pieces and coatings, this is our favorite. The manufacturer states 1 to 2 cm per pour, a working time of about one to two hours and a cure time of 16 to 24 hours; chemically, the resin is fully cured after about seven days. For the PRO line, EPODEX promises UV protection against yellowing, but the company does not publish any measurements for it. It is mixed 2:1 by weight.
EPODEX ECO System
The simpler line, with 1 cm per pour. For additional layers, EPODEX names a pause of about six hours. The product page does not mention UV protection. For pieces that stay indoors and out of the sun, that is acceptable; for the windowsill, less so.
EPODEX PRO MAX System
The table resin of the range. The manufacturer states up to 10 cm in a single pour, about eight hours of working time and 72 to 96 hours until cured. Bubbles are said to rise on their own at room temperature.
Resin Pro iCrystal
This Italian resin is intended for layers up to 1.5 cm at 20 °C. At 30 minutes, its pot life is tight. That is enough for earrings, but for a large surface it gets hectic. Resin Pro mentions UV filters against yellowing and recommends pigments in powder or paste form, not acrylic paints.
Resin Pro Trasparente
Also intended for fiberglass repairs. According to the data sheet: 100:60 by weight, pot life around 50 minutes, good hardness after 24 to 48 hours. According to the data sheet, it keeps for twelve months from filling when stored between 10 and 35 °C.
Resin Pro EpoxyTable 10
A slow resin for deep pours up to 10 cm. The pot life of 24 hours leaves plenty of calm for tinting. In return, you wait: demold after two to three days, fully cured after seven days, and that at a constant 25 °C. In a cool workshop, this shifts considerably.
Which resin for which project?
- Jewelry, coasters, pictures and coatings: EPODEX PRO System. If you work fast and like it very clear, look at Resin Pro iCrystal.
- River table in a single pour: EPODEX PRO MAX. If you can hold a constant 25 °C and have time, go for Resin Pro EpoxyTable 10.
- Repairs and fiberglass: Resin Pro Trasparente.
Our advice for your first purchase: start with a small pack and a test pour in a yogurt cup. That way you see how the resin behaves at your room temperature. Before 10 kg flow into the mold.
Frequently asked questions
Why can't you pour epoxy resin as thick as you like?
Epoxy resin cures through a chemical reaction that generates heat. In a thick pour, this heat builds up. Resin Pro states that large quantities can get hotter than 150 °C and limits a single pour of Trasparente to 250 g and no more than 2 cm. That is why manufacturers state a maximum pour depth per pour.
Which epoxy resin suits a river table?
One made for deep pours, such as EPODEX PRO MAX up to 10 cm with about eight hours of working time, or Resin Pro EpoxyTable 10 with 24 hours of pot life. A river channel of 120 × 20 cm at a depth of 4 cm needs a good ten kilograms of resin. With a resin rated for 2 cm, that would mean at least two pours.
What does pot life mean for epoxy resin?
It tells you how long mixed resin stays fluid enough to pour, and it depends on quantity and temperature. Resin Pro measures it at 150 g and 25 °C. With larger quantities in a bucket, the clock runs faster because the mass heats itself up. EPODEX recommends pouring immediately after mixing.
Which gloves do you need for epoxy resin?
According to BG BAU (the German employers' liability insurance association for the construction industry), protective gloves made of nitrile or butyl rubber that are tested for epoxy resin. Leather gloves and nitrile-impregnated cotton do not protect, and barrier cream does not replace gloves. Epoxy resins are highly allergenic, and an acquired allergy is permanent. When mixing, safety goggles, long sleeves and long pants are part of the equipment.
At what temperature should you work with epoxy resin?
EPODEX and Resin Pro name about 20 °C as the lower limit for the room, the workpiece and the resin. Below that, curing takes longer and thin layers can turn cloudy. According to EPODEX, freshly poured resin should not come into contact with water for about seven days, otherwise white spots may appear.
How do you dispose of leftover epoxy resin?
According to the DGUV (German Social Accident Insurance), cured epoxy resin does not trigger allergies and is not hazardous waste. So stir leftover resin and hardener together and let them cure instead of throwing them away liquid. Sanding later produces fine dust, and then a suitable dust mask is part of the job.
Sources
- EPODEX: PRO System
- EPODEX: ECO System
- EPODEX: PRO MAX System
- Resin Pro: iCrystal
- Resin Pro: technical data sheet Trasparente (PDF)
- Resin Pro: safety data sheet Trasparente hardener (PDF)
- Resin Pro: EpoxyTable 10
- BG BAU: Epoxy resins
- DGUV Information 201-062: Epoxy resins in the construction industry (PDF)
Where to buy
- EPODEX PRO SystemCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- EPODEX ECO SystemCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- EPODEX PRO MAX SystemCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Resin Pro iCrystalCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Resin Pro TrasparenteCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Resin Pro EpoxyTable 10Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
