Contents13 sections
This guide was first published in German on handgetestet.de.
Can a laser that cuts through plywood sit next to the dining table? Only if it is completely enclosed. For an apartment, we consider only an enclosed Class 1 device an option, and you plan the exhaust to the outside right along with it. We deliberately don’t single out one model, because the laser class for all four devices appears only in seller information.
Diode or CO2, work area and power are covered in our guide to buying a laser engraver (in German). This article asks a different question. What can go wrong at home, and what really protects against it?
How dangerous is a device like this?
In December 2024, the state government of North Rhine-Westphalia published a comparison that sticks. An ordinary laser pointer has at most one milliwatt, a laser engraving machine usually three to 30 watts. That is 3,000 to 30,000 times as much. In spot checks, inspectors found defects in all the products examined up to that point; protective shields were sometimes missing or easy to remove, and more than 300 listings disappeared from online shops.
Most of them use a Class 4 laser. With this class, according to the Bundesanstalt für Arbeitsschutz und Arbeitsmedizin (BAuA), Germany’s federal institute for occupational safety and health, any kind of exposure of the eyes or skin is expected to cause damage. The Deutsche Gesetzliche Unfallversicherung (DGUV), the German Social Accident Insurance, adds that diffuse radiation can also be dangerous. A reflection from a shiny part is enough.
Can I use an open Class 4 laser privately?
The BAuA puts it clearly. Consumer products may only be placed on the market in Classes 1, 1M, 2 or 2M. According to the BAuA, lasers of Classes 3R, 3B and 4 can only be used in a commercial setting under special protective measures, because the manufacturer cannot ensure safe use. This requirement is aimed at manufacturers, importers and retailers. What consequences it has for you as a private buyer cannot be derived from it.
Two examples show how far advertising and manuals can diverge. In its safety instructions for the EU and the UK, xTool classifies the F1 Ultra as Class 4, calls it a device for professional use and requires a laser safety officer. Atomstack likewise writes Class 4 in the manual for the X20, A20 and S20 Pro series. That is why you should read the manual before you pay.
If there is no information at all, a rule from the Swiss accident insurer Suva for businesses helps. There, an unknown class automatically means Class 4. That is how we would handle it too.
What does Class 1 mean at 20 watts?
It sounds contradictory, but it isn’t. Classification is based on the radiation that can escape to the outside. An enclosed laser is therefore considered Class 1, even if a much more powerful source works inside. The BAuA considers such enclosed lasers safe; laser safety glasses are then not necessary in normal operation.
That only applies as long as the housing is closed. When it is opened, the laser must stop immediately, as the warning from North Rhine-Westphalia also describes. If you bypass the lid switch or unscrew a shield, you are once again dealing with an open laser.
Also check which rule the class was assigned under. Some listings name an FDA class, which is a US requirement. What counts for Europe is classification according to EN 60825-1. In addition, North Rhine-Westphalia requires CE marking, the full address of the manufacturer or importer on the product, warnings and instructions in German (for the German market) and a declaration of conformity. If any of that is missing, leave the device in the shop.
Aren’t safety glasses enough?
No. In occupational safety, technical solutions come before personal equipment, and there are reasons for that. According to the BAuA, laser safety glasses according to DIN EN 207 only protect against accidental exposure, not against looking into the beam for longer. They must match the wavelength, their protection level is defined by a number and power density, and they must be tested by a notified body.
The OD5+ marking that Atomstack requires in its manual describes only the attenuation. Look for marking according to the standard. Ordinary safety glasses for the workshop (in German) are designed for chips and don’t help here. And everyone else in the room? They need a pair too, and children and pets shouldn’t be in there at all.
Where do the fumes go?
This is the point most often underestimated when buying. A housing holds back the beam, not gases. For laser marking of plastics, the DGUV has compiled which decomposition products occur. This 2015 edition has since been withdrawn, and it applies to commercial systems with other laser types. The list still works as a guide:
- PVC releases hydrogen chloride.
- PTFE releases fluorides and hydrogen fluoride.
- ABS releases styrene, 1,3-butadiene and acrylonitrile.
- POM releases formaldehyde, polycarbonate releases phenol.
- Polyacrylonitrile releases acrylonitrile and hydrogen cyanide.
According to the DGUV, the formation of carcinogenic substances cannot be ruled out with POM, ABS, SAN, polyethylene, PAN and PBT. Returning the filtered air to the room was not permitted there; venting to the outside was required. A tabletop filter sounds like a solution. With these substances, however, businesses were specifically not allowed to rely on one.
In its instructions, xTool requires the exhaust hose to be routed outside or into a suitable air purifier and prohibits blowing it into the room. So a spot by the window matters more than the power class. Wood, leather and paper, yes; plastic you can’t identify with certainty, no. Atomstack also advises against material with unknown properties.
And if something catches fire?
Flammable material can catch fire at low speed and high power, xTool writes. xTool and Atomstack therefore require the same thing. The device never runs unattended, and an extinguisher is within reach. xTool explicitly names CO2 extinguishers; the types are explained in our overview of fire extinguishers. Atomstack also requires a metal plate under the device. So stepping away for ten minutes to get coffee is not an option.
Four enclosed devices compared
| Model | Laser | Housing and class according to the seller | Best for |
|---|---|---|---|
| Creality Falcon A1C | 10 W diode | enclosed, Class 1 | Getting started in an apartment |
| xTool M2 | 10 W diode | enclosed, Class 1 | Crafting with wood, leather, felt |
| Sculpfun iCube Ultra | 12 W diode, 150 × 150 mm | enclosed, Class 1, smoke filter | little space, small parts |
| Creality Falcon A1 Pro | 20 W diode plus 2 W infrared | enclosed, Class 1 | more cutting power in an enclosure |
Creality Falcon A1C
Creality describes the A1C as a fully enclosed desktop engraver with a Class 1 design. On Amazon, it is available with a camera; the base version comes without. One listing mentions FDA Class 1, so the question of the European classification applies especially here.
xTool M2
On Amazon, the M2 is listed as an enclosed 10-watt device with Class 1 and two cameras, intended for wood, leather, felt, fabric and paper. At ten watts, it stays with thin material.
Sculpfun iCube Ultra
Small and enclosed. According to the Amazon listing, a door sensor stops the laser, plus there is an emergency stop, temperature sensor, USB safety key and smoke filter. The work area measures only 150 by 150 millimeters. The filter is no substitute for an exhaust path to the outdoors.
Creality Falcon A1 Pro
A 20-watt diode and 2-watt infrared in one housing, plus, according to Creality, flame detection, a stop when tilted and airflow monitoring. The housing is meant to filter the smoke. The Amazon listing names Class 1. According to the manufacturer, which module is included in the package depends on the version.
How we would decide
- Apartment, children in the household: enclosed only, Class 1 according to EN 60825-1 documented, hose to the window. Falcon A1C, xTool M2 or iCube Ultra depending on space.
- Thicker wood in a hobby basement: Falcon A1 Pro, if the exhaust leads outside.
- Large workpieces: clarify the class first, then the room. An open laser needs a separated area, the right glasses and a door nobody will open by accident.
- No window within reach: better not to buy. That applies to plastics anyway.
If you want to make parts from wood, a CNC router (in German) is also an option. For names and patterns on metal, an engraving tool (in German) without any beam is often enough.
Frequently asked questions
How dangerous is a laser engraver?
Very, if it is open. A laser engraving machine usually has three to 30 watts, a laser pointer at most one milliwatt. Most of them use a Class 4 laser, with which, according to the German occupational safety agency BAuA, any exposure of the eyes or skin can cause damage. According to the German statutory accident insurance DGUV, even a reflection from a shiny part is enough.
What does laser Class 1 mean for a 20-watt device?
Classification is based on the radiation that can escape to the outside. An enclosed laser is therefore considered Class 1, even if a more powerful source works inside. That only applies with the housing closed: when it is opened, the laser must stop immediately. Look for classification according to EN 60825-1, not just an FDA class.
Are safety glasses enough with an open laser?
No. According to the BAuA, laser safety glasses according to DIN EN 207 only protect against accidental exposure, not against looking into the beam for longer. They must match the wavelength and be tested by a notified body. A marking such as OD5+ only describes the attenuation; ordinary workshop safety glasses don't help.
Which materials can you laser at home?
Wood, leather and paper, yes; plastic you can't identify with certainty, no. PVC releases hydrogen chloride, POM formaldehyde, ABS styrene and acrylonitrile. According to the DGUV, carcinogenic substances cannot be ruled out with several plastics. Atomstack also advises against material with unknown properties.
Is a smoke filter in the laser engraver enough?
Not as a substitute for venting outdoors. A housing holds back the beam, not gases. xTool requires the exhaust hose to be routed outside or into a suitable air purifier and prohibits blowing it into the room. A spot by the window matters more than the power class.
Can a laser engraver run unattended?
No. Flammable material can catch fire at low speed and high power. xTool and Atomstack require that the device never runs unattended and that an extinguisher is within reach; xTool names CO2 extinguishers. Atomstack also requires a metal plate under the device.
Sources
- German Federal Institute for Occupational Safety and Health (BAuA): Laser radiation, guidance for risk assessment
- State of North Rhine-Westphalia: Warning about dangerous laser engraving machines sold online
- DGUV Information 203-095: Laser radiation on construction sites (overview of laser classes)
- DGUV Information 213-729: Laser marking of plastics, 2015 edition
- Suva: Laser classes, regulations and protective measures
- xTool: Safety instructions F1 Ultra (EU and UK)
- Atomstack: User manual X20, A20, S20 Pro
- Creality Falcon: Falcon A1 series
Where to buy
- Creality Falcon A1CCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- xTool M2Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Sculpfun iCube UltraCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Creality Falcon A1 ProCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
