Contents12 sections
This guide was first published in German on handgetestet.de.
An open diode laser with a big wattage figure on the outside, set up in the home office, with a pair of goggles from the accessory pack next to it. That is how many bad decisions begin. If you engrave in an apartment or a hobby basement, you are much better off with an enclosed machine in laser class 1, such as the xTool S1 or, if the budget is tighter, the Creality Falcon A1. A CO2 laser such as the xTool P2S is mainly for people who cut a lot of acrylic or work through orders.
Power is the wrong first question here. The enclosure, the exhaust and the materials you want to work with matter more.
Blue light or infrared: what is behind diode and CO2
Diode lasers work with blue light at around 455 nanometers. They are compact, need no water cooling and handle wood, leather, cardboard and coated metal well. Worth noting: in the cutting specifications for acrylic, the talk is usually of „dark“ acrylic.
A CO2 laser works at 10.6 micrometers in the infrared. According to xTool, the P2S processes acrylic in every color, glass, fabric, leather and wood. In return, these machines are larger and heavier. They need cooling and cost several times as much. For metal, xTool and Sculpfun offer additional infrared modules at 1,064 nanometers.
One more word on wattage. It should refer to the optical output power, not the power consumption. Advertising claims such as „120 W“ often refer to the power supply. So always compare laser power with laser power.
Laser class, enclosure and safety goggles: what the authorities say
In December 2024, the occupational safety authority of the German state of North Rhine-Westphalia warned about laser engraving machines sold online. According to the state government, most of these machines work with a class 4 laser that can permanently damage the eyes and burn the skin, including through reflections. The inspectors found defects in every product they examined; in some cases, protective screens were missing or could easily be removed. More than 300 listings were taken down.
The authority describes a safe machine like this: the laser is fully enclosed and stops immediately when a flap is opened. This includes CE marking, the manufacturer’s address, German-language instructions and warning notices. According to the documents of the German Federal Institute for Occupational Safety and Health (BAuA), an enclosed laser counts as class 1 even if a more powerful source sits inside. According to the BAuA, class 1 means safe under intended use.
With open machines, safety goggles remain mandatory. They must match the laser’s wavelength, as xTool, for example, states in its safety instructions. There are no goggles that protect against every laser. The relevant standard is DIN EN 207. Goggles without a stated wavelength and protection level are not laser safety goggles.
Smoke is the underestimated problem
A laser vaporizes material, and those fumes end up in the air you breathe unless something carries them away. The German Social Accident Insurance (DGUV) has examined which substances are produced when plastics are marked with lasers. With PVC, it is hydrogen chloride; with ABS, styrene and acrylonitrile, among others. The DGUV information names extraction directly at the source, combined with an enclosed design, as the most effective solution.
In its safety instructions, xTool advises routing the exhaust outdoors or into a suitable air purifier, never openly into the room. The manufacturer explicitly names PVC, vinyl, ABS and polycarbonate as problematic. And: never leave the machine running unattended, and keep a CO2 fire extinguisher within reach. A spot by the window with an exhaust hose is therefore worth more than ten extra watts.
Five points for your checklist
- Laser class on the rating plate and in the manual, not just in the advertising copy.
- Lid switch, emergency stop and key switch against unauthorized use, which matters in households with children.
- Exhaust connection with hose diameter, plus the route to the window.
- A work area that suits your workpieces. An A3-size area is enough for signs and cutting boards.
- Software: the manufacturers‘ own programs are often simpler, while LightBurn offers more control.
Five machines currently available on Amazon.de
| Model | Laser | Work area | Enclosure and class | Best for |
|---|---|---|---|---|
| xTool S1 | Diode, 20 or 40 W | approx. 498 × 319 to 333 mm | enclosed, class 1 | Hobby use in an apartment, small batches |
| Creality Falcon A1 | Diode, 10 W | 305 × 381 mm | enclosed, class 1 | Getting started on a small budget |
| Atomstack A24 Ultra | Diode, 24 W | approx. 365 × 305 mm | Protective box with camera, class 1 according to the manual | More cutting power inside an enclosure |
| Sculpfun S30 Ultra 22W | Diode, 22 W | 590 × 595 mm | open, protective shield | Large workpieces in the workshop |
| xTool P2S | CO2, 55 W | 600 × 308 mm | enclosed, class 1 or 4 depending on version | Lots of acrylic, small businesses |
xTool S1: the enclosed diode laser with a large work area
For the S1, xTool states laser class 1 according to the IEC standard, along with five flame sensors, a stop when the lid is opened and a key switch. According to xTool, the cover filters more than 99 percent of the blue light. The 40 W version cuts thicker wood in fewer passes; for engraving, 20 W is enough. An infrared module for metal and a rotary axis for mugs are available at extra cost.
Creality Falcon A1: an entry-level machine with an enclosure
Price-wise, the Falcon A1 sits a class below the S1. It is enclosed all the same. Creality states 10 W of optical power, 455 nanometers and laser class 1. A camera helps with alignment. That is not enough power to cut thick boards, but it is sufficient for engraving wood and leather.
Atomstack A24 Ultra: more power, confusing names
According to the user manual, the A24 Ultra works with 24 W and belongs to class 1. On Amazon.de, it is listed with a protective box and camera. Be careful when comparing: Atomstack also sells the A24 Pro and A24 Pro Ultra, some without an enclosure. Check carefully which bundle is in your cart.
Sculpfun S30 Ultra 22W: lots of space, but open
A work area of 590 by 595 millimeters, automatic air assist at 30 liters per minute, emergency stop and a key-operated child lock: those are the manufacturer’s specifications. There is no enclosure; only a removable protective shield on the head covers the beam. A machine like this does not belong in an apartment. In a ventilated workshop, with suitable safety goggles and an enclosure of your own, it can be a solution for large workpieces.
xTool P2S: CO2 for anyone who cuts acrylic
The P2S works with a 55 W CO2 tube and closed-loop water cooling. It also has two cameras with 16 megapixels each. According to the manufacturer, it cuts acrylic in every color up to 20 millimeters thick. Versions in class 1 and class 4 are available in stores. For purely hobby engraving, it is hardly worth it.
Which laser for which workbench?
- You engrave in your apartment and occasionally cut plywood: xTool S1 with 20 W, plus an exhaust hose to the window.
- You first want to find out whether lasering will become your hobby: Creality Falcon A1.
- You need more cutting power but do not want to work with an open machine: Atomstack A24 Ultra, after checking the bundle.
- Large boards in a ventilated workshop: Sculpfun S30 Ultra 22W, only with suitable safety goggles.
- Acrylic, glass and fabric in series: xTool P2S in the class 1 version.
Engraving small parts by hand? An engraving tool or Dremel (in German) is often enough for that. For making your own parts, a laser pairs well with a 3D printer, and the hand tools to go with it are covered under model-making tools (in German).
Laser class, smoke and safety goggles are covered in the guide Laser engravers at home.
Frequently asked questions
What is the difference between a diode laser and a CO2 laser?
Diode lasers work with blue light at around 455 nanometers, are compact and handle wood, leather, cardboard and coated metal well, but usually only dark acrylic. According to xTool, a CO2 laser also processes acrylic in every color, glass and fabric, but it is larger, needs cooling and costs several times as much.
What does laser class 1 mean for a laser engraver?
According to the documents of the German Federal Institute for Occupational Safety and Health (BAuA), an enclosed laser counts as class 1 even if a more powerful source sits inside. Class 1 means safe under intended use. Most machines sold online, by contrast, work with class 4, which can permanently damage the eyes and burn the skin.
How do you recognize a safe laser engraver?
According to the occupational safety authority of the German state of North Rhine-Westphalia, the laser is fully enclosed and stops immediately when a flap is opened. This includes CE marking, the manufacturer's address, German-language instructions and warning notices. An emergency stop and a key switch against unauthorized use are also helpful, which matters in households with children.
Which safety goggles do you need for an open laser?
The goggles must match the laser's wavelength; there is no pair that works for every laser. The relevant standard is DIN EN 207. Goggles without a stated wavelength and protection level are not laser safety goggles.
Does a laser engraver need an exhaust?
Yes. The laser vaporizes material; according to the German Social Accident Insurance (DGUV), PVC releases hydrogen chloride, and ABS releases styrene, among other substances. xTool advises routing the exhaust outdoors or into a suitable air purifier, never openly into the room. A spot by the window with an exhaust hose is worth more than ten extra watts.
What does the wattage of a laser engraver tell you?
It should refer to the optical output power, not the power consumption. Advertising claims such as 120 W often refer to the power supply. So always compare laser power with laser power. For engraving wood and leather, 10 W is enough; cutting thick wood in fewer passes takes more.
Sources
- State of North Rhine-Westphalia: Warning about dangerous laser engraving machines sold online
- BAuA: Guidance on risk assessment for laser radiation
- DGUV Information 213-729: Marking plastics with lasers
- xTool: Safety instructions
- xTool: Safety features and certifications
- xTool S1
- Creality Falcon A1
- Atomstack A24 Ultra
- Sculpfun S30 Ultra 22W
- xTool P2S
Where to buy
- xTool S1Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Creality Falcon A1Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Atomstack A24 UltraCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Sculpfun S30 Ultra 22WCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- xTool P2SCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
