Contents11 sections
This guide was first published in German on handgetestet.de.
With a LiPo charger, it is rarely power that is missing once you unpack it. It is the power supply. Many compact chargers run on DC only, and if you only notice that at home, you are left without power. For hobbyists with individual 2S to 6S packs, a small DC charger such as the SkyRC B6neo+ with a documented storage mode is usually enough, together with a suitable USB-C or XT60 power supply.
Where the power comes from determines the watts
The advertised wattage almost always applies only with a powerful DC power supply. On mains power or USB-C, the same devices often deliver considerably less. A rough calculation helps: a 4S pack of 5,000 mAh needs around 5 A at 1C, which means just under 85 watts. For a 6S pack with the same capacity, it is already about 125 watts.
That leads to the first question for any device: the input. Built-in power supply (AC), DC only, or USB-C PD? Without a built-in power supply, you need a second device.
Cells, balancer, storage mode
All the chargers listed here handle 1S to 6S. If you run 8S, you need a different class.
Less obvious but noticeable in everyday use is the balancing current, because it determines how quickly uneven cells are equalized; according to the manufacturers, the range runs from 0.6 to 1.5 A per cell. Not every charger can discharge a full pack to storage voltage, either. Whether it can is stated in the manual. Check beforehand! Finally, two or four outputs only pay off if several packs are regularly empty at the same time.
We have compiled connectors and tools for plugs and cables in our guide to model building tools (in German).
Storage voltage and safe charging according to the sources
In the manual for the B6neo+, SkyRC gives a storage voltage of 3.8 V per cell for LiPo and 3.85 V for LiHV. For LiPo, the manufacturer specifies a maximum charging current of 1C unless the battery manufacturer allows otherwise. So a pack that sits in the cupboard for weeks after flying or driving should go there neither full nor empty.
On charging itself, the sources are remarkably consistent. In their manuals, SkyRC and ToolkitRC say never to charge batteries unattended, and SkyRC adds: not overnight, not on carpet or a car seat, and away from flammable material. The Institut für Schadenverhütung und Schadenforschung der öffentlichen Versicherer (IFS), the loss prevention and research institute of the German public insurers, advises charging in a fire-safe spot, for example on a stone floor, equipping the room with a smoke alarm and not charging overnight in living areas. According to the IFS, the first charge after a pause of several months is especially critical, as is any battery that has been dropped and damaged. The Swiss fire prevention advisory body bfb (Beratungsstelle für Brandverhütung) adds: replace swollen or cracked batteries immediately and never charge in hallways or stairwells, because those are escape routes.
And the LiPo safe bag? It is widely sold and can add an extra enclosure around the battery while charging. However, the bodies cited do not document how reliably a particular bag contains a battery fire. See it as a supplement to the fireproof surface and to supervision, not as a replacement.
Five chargers for LiPo batteries compared
| Model | Input | Output according to manufacturer | Best for |
|---|---|---|---|
| SkyRC B6neo+ | DC 5–30 V, USB-C PD | 240 W (DC), 126 W (PD), 1 channel | Beginners with individual packs |
| ISDT 608PD | DC 5–30 V, USB-C PD 3.1 | 240 W, up to 10 A, 1 channel | On the go at the flying field |
| ToolkitRC M6AC | Mains 100–240 V or DC 7–28 V | up to 300 W, 15 A, 1 channel | Workbench without an extra power supply |
| ISDT K2 Air | Mains 100–240 V or DC 10–30 V | 200 W (mains), 2 × 500 W (DC) | Two batteries at once |
| ToolkitRC Q6AC | Mains 100–240 V or DC 7–30 V | 400 W (mains), 1,200 W (DC), 4 channels | Clubs, frequent FPV flyers |
SkyRC B6neo+: small, with storage mode
According to the manual, the B6neo+ charges LiPo, LiIon, LiFe and LiHV from 1S to 6S and explicitly offers a storage mode. At the XT60 input, 240 watts are possible; via USB-C PD, up to 126 watts. Conversely, it can also discharge a pack via USB-C into a laptop or phone, according to SkyRC at a maximum of 100 watts. At no more than 600 mA, the balancer works at a rather leisurely pace. According to retailers, no power supply is included.
ISDT 608PD: pocket-sized with strong USB-C
The 608PD draws power via XT60 or USB-C PD 3.1; according to ISDT, it charges at 0.5 to 10 A with a maximum of 240 watts. The balancer manages 0.8 A per cell. The manufacturer’s page makes no mention of a dedicated storage mode. If you often need to bring full packs down to storage voltage, the SkyRC is the better choice.
ToolkitRC M6AC: power supply built right in
The M6AC plugs directly into a wall outlet or runs on 7 to 28 V DC. ToolkitRC promises 15 A and a maximum of 300 watts, plus storage mode, internal resistance measurement and a signal tester for PWM, PPM and SBUS. According to retailers, output on mains power is considerably lower than with a DC power supply. It handles individual 3S and 4S packs well that way. With large 6S packs, it gets slow.
ISDT K2 Air: two channels and an app
Two independent outputs at 0.2 to 20 A each, 200 watts on mains power, 2 × 500 watts with a DC power supply: that is how ISDT describes the K2 Air. Its balancer works at up to 1.5 A per cell, and it can also be controlled via the ISD Link app. It only reaches the full 500 watts per channel with a correspondingly large DC power supply. On mains power, it stays at 200 watts.
ToolkitRC Q6AC: four outputs for many packs
Four channels at 0.1 to 15 A and 250 watts each, up to 400 watts in total on mains power, and up to 1,200 watts on DC via XT90. On top of that, USB-C with 65 and USB-A with 30 watts. With two batteries, the price hardly makes sense. If you head to the field with five FPV packs, you will see it differently. ToolkitRC does not mention a storage mode for the Q6AC.
Graupner is deliberately missing. Retailers currently list chargers from the Polaron series mostly as sold out or no longer available.
Which charger suits which hobby
For your first LiPo and one to three packs, we recommend the SkyRC B6neo+ with a USB-C power supply: small, storage mode documented, slow balancer. If you do not want a second device on the workbench, take the ToolkitRC M6AC, as long as large 6S packs remain the exception. Charging at the flying field from a portable power station or car battery? Then the ISDT 608PD, though without a stated storage mode.
For an RC car with two drive batteries, the ISDT K2 Air fits; suitable cars are in our comparison of remote-controlled cars. FPV with many small packs points to the ToolkitRC Q6AC. If you are just getting started, the article on the FPV drone for beginners gives you the framework.
From our hands-on test: the Hyper Go H16BM from AMEWI comes with two 2S batteries; with optional 3S batteries, according to the manufacturer, it should reach up to 68 km/h instead of about 45. If you upgrade like that, choose a charger that handles both cell counts.
Whatever the device: charging power is half the battle, the charging spot is the other half. Stone floor, smoke alarm, no escape route, and someone within earshot.
How to charge LiPo batteries safely in an RC boat and how to handle them after a run is explained in our RC boat guide, with seven boats in a data comparison.
Frequently asked questions
Does a LiPo charger need a separate power supply?
Often, yes. Many compact chargers run on DC only, such as the SkyRC B6neo+ or the ISDT 608PD. The advertised wattage usually applies only with a powerful DC power supply; on mains power or USB-C, the same devices deliver considerably less. Devices such as the ToolkitRC M6AC have the power supply built in.
How many watts does a charger need for 4S and 6S packs?
A 4S pack with 5,000 mAh needs around 5 A at 1C, which means just under 85 watts. For a 6S pack with the same capacity, it is about 125 watts. Check what output the device actually delivers from your power source, not just from its strongest input.
What is the storage voltage for LiPo batteries?
In the manual for the B6neo+, SkyRC states 3.8 V per cell for LiPo and 3.85 V for LiHV. A pack that will sit for weeks should go into the cupboard neither full nor empty. Not every charger can discharge to storage voltage; for the ISDT 608PD and ToolkitRC Q6AC, the manufacturers do not mention a storage mode.
How do you charge LiPo batteries safely?
SkyRC and ToolkitRC say never to charge batteries unattended, SkyRC also not overnight and not on carpet. The German insurers' institute IFS advises a fire-safe spot such as a stone floor and a smoke alarm in the room. According to the Swiss bfb, swollen batteries should be replaced immediately, and you should never charge in hallways or stairwells.
Is a LiPo safe bag enough fire protection?
As a supplement, it can add an extra enclosure around the battery while charging. The bodies cited do not document how reliably a particular bag contains a battery fire. It replaces neither the fireproof surface nor supervision while charging.
When is a charger with several channels worth it?
Two or four outputs only pay off if several packs are regularly empty at the same time. For an RC car with two drive batteries, the ISDT K2 Air fits; for FPV with many small packs, the four-channel ToolkitRC Q6AC. With two batteries, its price hardly makes sense.
Sources
- SkyRC B6neo+, user manual (specifications, storage voltage, safety instructions)
- ISDT 608PD, manufacturer page
- ISDT K2 Air, manufacturer page
- ToolkitRC M6AC, user manual V1.1
- ToolkitRC Q6AC, manufacturer page
- IFS, safety tips for lithium-ion batteries (e-bikes and model building)
- bfb, fact sheet „More safety with lithium-ion batteries“
Where to buy
- SkyRC B6neo+Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- ISDT 608PDCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- ToolkitRC M6ACCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- ISDT K2 AirCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- ToolkitRC Q6ACCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
