Contents16 sections
This guide was first published in German on handgetestet.de.
A smart thermostat rarely fails because of the app. It fails because of the valve the old knob used to sit on. For anyone who gets stuck on a Danfoss valve, the ELV adapter set for RA, RAV and RAVL is the most sensible choice, because it covers all three designs from the Danish manufacturer and eQ-3 includes the matching mounting hardware. For everyone else, the first step is simply this: check what is actually installed.
This guide explains how to identify a valve body, why a few millimeters at the valve pin decide between success and an error message, and which adapter belongs on which valve. Which thermostat goes on afterward is covered in our guide to smart radiator thermostats (in German). Here, it is only about the small piece in between.
M30 x 1.5: the standard case many people already have
Electronic radiator thermostats such as those from Homematic IP or Eqiva are screwed on with a union nut on an M30 x 1.5 thread. That means a diameter of 30 millimeters and a pitch of 1.5 millimeters. According to eQ-3’s valve compatibility list, Heimeier, Honeywell-Braukmann, Junkers, IVAR, Jaga, Siemens and Watts use this size. Newer Oventrop valves and some Comap valves fit it as well. If you have one of these valves, you do not need an adapter.
The trouble comes from the special cases. Danfoss uses a clamp connection instead of a thread. Vaillant has its own 30.5-millimeter connection. Herz, TA, Markaryds and SAM work with M28 x 1.5, older Oventrop valves with M30 x 1.0. Then there are rarities such as Giacomini with 22.6 millimeters, Ista with M32 x 1.0 or Rossweiner with M33 x 2.0. According to eQ-3, the rule is: if a valve is not on the list, there is currently no matching adapter for it.
Read the valve before you order
First pull off the old thermostat head and look at what is left. Usually the manufacturer appears as an embossed mark or logo on the valve body, sometimes only on the old head. A small „OV“ gives away Oventrop, and „TA“ stands for the manufacturer of the same name. You can recognize Danfoss by a notched collar instead of an external thread.
Without a logo, a caliper helps. Measure the outside diameter of the thread or collar and count the notches. The eQ-3 list gives 23 millimeters with four notches for Danfoss RA, 25.5 millimeters for RAVL and 34 millimeters for RAV, each also with four notches. A photo of the valve from above and from the side helps later when comparing with the pictures in the list. If you are unsure whether it is M30 x 1.5 or M30 x 1.0, you can test-fit an old nut from a thermostat head. If it stops catching after half a turn, the pitch is wrong.
Danfoss: three designs, one clamp principle
RA, RAV and RAVL look similar but are not interchangeable. Danfoss itself states that its current RA-N valve bodies work with all Danfoss thermostat heads with an RA connection. Because of their different diameters, RAV and RAVL each need their own adapter.
An adapter for Danfoss is not screwed on but clamped. This is exactly where most installation mistakes happen. eQ-3’s information sheet on the RA adapter describes them: the adapter has to be bent open slightly without the screw inserted and pushed all the way onto the valve. Only then does the screw go in. If it sits crooked, the thermostat cannot find the closing point during its calibration run and reports an error, such as „F2“. As a check, eQ-3 gives a measurement: between the adapter’s contact surface and the valve tappet there should be about 13.5 millimeters with the valve open, and about 11.5 with the pin pressed in.
Many thermostats already come with Danfoss adapters. According to eQ-3, most Homematic IP radiator thermostats include all three Danfoss adapters, while the „basic“ version only includes the RA adapter. So check the box before you buy more.
Closing dimension: the millimeters everything depends on
A thermostat closes the valve by pushing the valve pin down. How far the pin has to travel for that differs from manufacturer to manufacturer. The adapter compensates for this closing dimension with an extension pin. If the pin is too short, the valve stays open a crack and the radiator never gets completely cold. If it is too long, the valve already closes at a middle setting.
The instructions for the eQ-3 adapter for M28 x 1.5 show how finely graded this is. Four pins are included, 15, 17, 18.5 and 24 millimeters long. Which one fits depends on the manufacturer or on the measured closing dimension: press the valve pin all the way in, measure the height, look it up in the table. At 6.5 to 8.5 millimeters it is the 18.5-millimeter pin; at only 1 to 3 millimeters, the longest. Two minutes with the caliper save a lot of guesswork later.
Brass or plastic?
Both are offered, often for the same valve. According to the data sheet, an eQ-3 plastic adapter weighs 13 grams, and according to the instructions, the threaded versions are screwed on hand-tight without tools. Brass adapters, at ELV (German retailer) for example from EUROtronic, sit one price class higher. A customer review at ELV reports that the included plastic parts did not hold on their valve and only brass solved the problem. That is a single case, but a plausible one. A radiator on a hallway wall that children or vacuum cleaners bump into is better served with brass. In the guest room, plastic is enough.
Removing the old head without surprises
You do not have to drain any water. The eQ-3 instructions do point out something that surprises many people, though: without the thermostat head, the valve opens fully. The radiator and connections can then get very hot. Turn off the heating during installation or shut off the radiator at the return fitting. If there is rust, cracks or a dripping valve, the job belongs in the hands of a professional heating contractor.
One more distinction. The Möhlenhoff valve adapters of the VA series, which ELV also carries, are intended for actuators like those found on heating circuit manifolds. If you want to control underfloor heating smartly (in German), that is where you will end up. They are not designed for the knob on a radiator.
Seven adapters and where they belong
| Model | Fits | Material and connection | Best for |
|---|---|---|---|
| ELV adapter set Danfoss RA, RAV, RAVL | Danfoss RA, RAV, RAVL (clamp connection) | Plastic, three adapters, tappet extension, M4 screw and nut, M30 x 1.5 output | anyone with Danfoss valves, including a mixed set of valves |
| Vaillant 30.5 mm adapter (plastic) | Vaillant 30.5 mm | Plastic, with clamps, screw and nut | homes with Vaillant valve bodies |
| Herz, Comap M28 x 1.5 adapter (plastic) | Herz, Comap, TA, MMA, SAM and others | Plastic, four extension pins | M28 valves, if you want to measure the closing dimension |
| Oventrop M30 x 1.0 adapter (plastic) | older Oventrop valves M30 x 1.0 | Plastic, with extension pin | Oventrop with a fine thread |
| Herz M28 x 1.5 heating valve adapter (brass) | Herz M28 x 1.5 | Brass | radiators that take a lot of wear |
| Giacomini 22.6 mm heating valve adapter (brass) | Giacomini 22.6 mm | Brass | older buildings with Italian valves |
| Ista M32 x 1.0 adapter (brass) | Ista M32 x 1.0 | Brass | apartments with Ista valves |
Specifications according to eQ-3 (data sheet, instructions, compatibility list) and according to ELV.
ELV adapter set Danfoss RA, RAV, RAVL
Made by eQ-3; the data sheet lists three adapters, a tappet extension, an M4 nut and an M4 x 12 cheese-head screw. According to the manufacturer, it fits Homematic, Homematic IP, MAX! and Eqiva thermostats as well as other controllers with M30 x 1.5. The advantage is trivial and still decisive: you do not need to know in advance whether RA or RAVL is installed. Drawback: plastic and clamp mounting require care when pushing it on.
Vaillant 30.5 mm adapter (plastic)
The Vaillant valve has no thread a thermostat could grip. According to the instructions, you fit the adapter so that its flattened edge lies parallel to one side of the hexagon, and secure it with clamps. The brass version at ELV requires a 2-millimeter hex key for this.
Herz, Comap M28 x 1.5 adapter (plastic)
The most versatile adapter on the list, because M28 x 1.5 is used by several manufacturers. According to eQ-3, the four pins cover closing dimensions of about 1 to 12 millimeters. If you measure carefully here, you will end up with a thermostat that really closes and opens.
Oventrop M30 x 1.0 adapter (plastic)
Only for the older Oventrop variant with a 1.0-millimeter pitch. Newer Oventrop valves with M30 x 1.5 do not need an adapter. They are easy to mix up because the diameter is the same. The test with an old union nut settles it.
Herz M28 x 1.5 heating valve adapter (brass)
Same connection as the plastic part, but made of brass by EUROtronic. A choice for radiators that have to withstand some mechanical stress. ELV does not list a set of extension pins for this version, so you should know the closing dimension beforehand.
Giacomini 22.6 mm heating valve adapter (brass)
Giacomini appears in the eQ-3 list with 22.6 millimeters. Rare, but if you have such a valve, you will find hardly any alternatives.
Ista M32 x 1.0 adapter (brass)
Many people know Ista as a metering service company; eQ-3 lists its valves with M32 x 1.0. According to ELV, the brass adapter comes from IMI Heimeier. In a rented apartment, the rule still applies: only change the valve and adapter if the landlord has no objection, and keep the old head.
How we would decide
- Danfoss collar with notches, design unclear: the ELV adapter set, but check the thermostat box first.
- M30 x 1.5 thread: no adapter, install directly.
- M28 x 1.5 from Herz, Comap or TA: the plastic adapter with four pins if you want to determine the closing dimension yourself; brass if the radiator takes a lot of knocks.
- Vaillant, older Oventrop, Giacomini, Ista: exactly the adapter for that valve, nothing universal.
- Valve is on no list: ask a professional heating contractor whether a new valve body makes more sense.
If you are planning to retrofit the whole apartment anyway, you should also consider a smart room thermostat. If you are renovating the bathroom at the same time, you will find tips in the guide to the towel radiator (in German).
Similar rules apply to the valves on the heating circuit manifold of underfloor heating; see the guide replacing an actuator.
Devices without wireless and app are compared in the guide to the programmable radiator thermostat.
Frequently asked questions
Do I need an adapter for my radiator thermostat?
Not with M30 x 1.5. According to eQ-3, this thread is used by Heimeier, Honeywell-Braukmann, Junkers, IVAR, Siemens and Watts, among others, as well as newer Oventrop valves. You need an adapter for the special cases such as Danfoss with its clamp connection, Vaillant with 30.5 millimeters or Herz with M28 x 1.5.
How do I identify my radiator valve?
Pull off the old head and look for an embossed mark or logo on the valve body; a small OV stands for Oventrop. You can recognize Danfoss by the notched collar. Without a logo, a caliper helps: according to eQ-3, Danfoss RA measures 23, RAVL 25.5 and RAV 34 millimeters.
Why does the thermostat show an error on a Danfoss valve?
Usually the clamp adapter is sitting crooked. According to eQ-3, it has to be bent open slightly without the screw and pushed all the way onto the valve; only then does the screw go in. Otherwise the thermostat cannot find the closing point during its calibration run and reports an error such as F2.
What is the closing dimension of a valve adapter?
The distance the valve pin has to travel to close, which varies by manufacturer. The adapter compensates for it with an extension pin. If the pin is too short, the radiator never gets completely cold; if it is too long, the valve already closes at a middle setting.
What is the difference between brass and plastic adapters?
According to eQ-3, plastic adapters are screwed on hand-tight without tools; brass adapters sit one price class higher. A radiator on a hallway wall that children or vacuum cleaners bump into is better served with brass; in the guest room, plastic is enough.
Do I have to drain water to change a thermostat?
No. Without the thermostat head, however, the valve opens fully, and the radiator and connections can get very hot. Turn off the heating during installation or shut off the radiator at the return fitting. If there is rust, cracks or a dripping valve, the job belongs in the hands of a professional heating contractor.
Sources
- eQ-3: Valve compatibility list V2.2 (PDF)
- eQ-3: Data sheet Danfoss adapter set (PDF)
- eQ-3: Notes on the Danfoss RA valve adapter (PDF)
- eQ-3: Installation instructions M28 x 1.5 adapter (PDF)
- eQ-3: Installation instructions Vaillant adapter (PDF)
- eQ-3: Installation instructions Oventrop adapter (PDF)
- Danfoss: RA-N valve body
- ELV: Adapter set Danfoss RA, RAV, RAVL (retailer information)
- ELV: Heating valve adapter Vaillant 30.5 mm, brass (retailer information)
- ELV: Adapter Ista M32 x 1.0, brass (retailer information)
Where to buy
- ELV Adapter-Set Danfoss RA, RAV, RAVLView at ELVAvailable in Germany: ELV
- Adapter Vaillant 30,5 mm (Kunststoff)View at ELVAvailable in Germany: ELV
- Adapter Herz, Comap M28 x 1,5 (Kunststoff)View at ELVAvailable in Germany: ELV
- Adapter Oventrop M30 x 1,0 (Kunststoff)View at ELVAvailable in Germany: ELV
- Heizungsventiladapter Herz M28 x 1,5 (Messing)View at ELVAvailable in Germany: ELV
- Heizungsventiladapter Giacomini 22,6 mm (Messing)View at ELVAvailable in Germany: ELV
- Adapter Ista M32 x 1,0 (Messing)View at ELVAvailable in Germany: ELV
- eQ-3 Adapter-Set Danfoss RA, RAV, RAVLCheck price at Amazon.deAvailable in Germany: Amazon.de
- Homematic IP HeizkörperthermostatCheck price at Amazon.deAvailable in Germany: Amazon.de
- tado Smartes HeizkörperthermostatCheck price at Amazon.deAvailable in Germany: Amazon.de

