Contents13 sections
This guide was first published in German on handgetestet.de.
Which spool should sit next to the new printer first? Our answer is a sober one: PLA at 1.75 millimeters, one kilogram, in a color you will actually print with. If you have a Bambu Lab machine with AMS, take Bambu Lab PLA Basic, because the AMS reads the settings from the spool’s RFID chip. PETG comes next as soon as parts are exposed to heat or load. ABS and TPU are special cases. One needs an enclosed printer and fresh air, the other patience.
Does every spool fit every printer?
No. The diameter comes first. 1.75 and 2.85 millimeters are not interchangeable; which one fits is stated in your printer’s data sheet. All six filaments below are available in 1.75 millimeters, and Extrudr also offers PLA NX2 in 2.85 millimeters.
Then comes tolerance. Prusa specifies ±0.02 mm for Prusament PETG, Bambu Lab ±0.03 mm for PLA Basic and ABS, and Sunlu ±0.02 mm for its TPU. Hundredths of a millimeter sound petty, but they are not: a strand of 1.80 instead of 1.75 mm pushes around six percent more plastic through the nozzle. You can see that in the walls and dimensional accuracy. Prusa goes one step further here and discloses, via QR code for every Prusament spool, the values measured during production, namely the diameter profile, weight, length and ovality.
The spool itself also deserves a look. Bambu Lab winds PLA Basic onto an ABS spool that, according to the data sheet, withstands up to 70 °C, and the ABS filament onto a spool of PC and ABS rated up to 90 °C. Both measure 200 mm in diameter and 67 mm in height. If you already own Bambu spools, you can go for the refill without a spool and fit the coil onto the old spool. Before buying a multicolor system or a dry box, you should know exactly these dimensions.
PLA, PETG, TPU or ABS: what is each good for?
PLA prints at 190 to 230 °C and gets by with a lukewarm bed. Figures, replacement knobs, organizers, prototypes. Its limit is heat. Bambu Lab specifies a heat deflection temperature of 54 °C for PLA Basic, and Polymaker 52 °C for PolyTerra PLA (each to ISO 75 at 1.8 MPa). For a mount that hangs behind the windshield in summer, that is cutting it too close.
PETG closes that gap. Prusa specifies 68 °C for Prusament PETG and recommends 250 °C at the nozzle and 80 °C on the bed, and it does not require an enclosed build chamber. As weaknesses, Prusa itself names stringing and very strong adhesion to the build plate. So take care when removing parts.
TPU is rubbery. Sunlu specifies an elongation at break of over 900 percent for its TPU 95A. Not every multicolor system can handle such soft material: Bambu Lab itself declares its TPU 95A HF unsuitable for the AMS and offers a harder „TPU for AMS“ with Shore 68D instead.
ABS withstands the most heat. Bambu Lab specifies 84 °C (at 1.8 MPa), but in return requires 240 to 270 °C at the nozzle, 80 to 100 °C on the bed and a chamber temperature of 45 to 60 °C. According to the manufacturer, ABS warps easily, which is why Bambu Lab explicitly prescribes an enclosed printer.
Does filament really need to go in the dryer?
Often, yes, and sooner than many people think. Before printing, Bambu Lab recommends 50 °C for eight hours in a convection oven for PLA Basic, and 80 °C for eight hours for ABS. Polymaker specifies 55 °C for six hours for PolyTerra PLA. According to Bambu Lab, filament should be stored and printed below 20 percent humidity, sealed and with desiccant. The manufacturer describes the TPU 95A HF as very sensitive to moisture.
How quickly materials absorb water varies widely. For its PETG, Prusa measures an uptake of only 0.10 percent after seven days at 22 percent humidity. Polymaker gives a saturation value of 0.36 percent at 70 percent humidity for PolyTerra PLA. An airtight box with desiccant and a small hygrometer are therefore the simplest insurance against stringing, bubbles and brittle parts.
Drying holds a second pitfall. The spool gets too hot. A Bambu Lab PLA spool is rated up to 70 °C; set ABS temperatures and you risk a warped spool.
How dangerous are the fumes from printing?
The Institute for Occupational Safety and Health of the German Social Accident Insurance (IFA/DGUV) measured a desktop printer with seven filaments in a test chamber and converted the values to a small single office with the windows closed. For PLA, PET, flexible filament, nylon and PE, the volatile organic compounds were at least an order of magnitude below the guideline values. ABS was the exception. For styrene, the result was 0.012 mg/m³, in the same order of magnitude as the indoor guideline value of 0.03 mg/m³. The hotter the nozzle and bed, the more particles the researchers detected.
This leads to simple rules: run the printer in a separate room if possible, do not point the exhaust at your desk, and ventilate before and after every print. For schools, the DGUV recommends airing out thoroughly with windows wide open at least after every print job. For ABS, Bambu Lab advises a well-ventilated room or effective filtration or extraction and explicitly names styrene. That is why ABS does not belong in a child’s room.
Six filaments with data sheets compared
| Filament | Material, Ø and tolerance | Nozzle / print bed according to manufacturer | Best for |
|---|---|---|---|
| Bambu Lab PLA Basic | PLA, 1.75 mm ±0.03 mm, RFID | 190–230 °C / 35–45 °C | Bambu printers with AMS, getting started |
| Polymaker PolyTerra PLA | PLA, 1.75 mm | 190–230 °C / 25–50 °C | Models and decor on any printer |
| Extrudr PLA NX2 Matt | Matte PLA, 1.75 or 2.85 mm | 200–230 °C / 20–60 °C | Matte surfaces, made in Austria |
| Prusament PETG | PETG, 1.75 mm ±0.02 mm | 250 ±10 °C / 80 ±10 °C | Holders, clips, outdoor parts |
| Sunlu TPU 95A | TPU Shore 95A, 1.75 mm ±0.02 mm | 190–230 °C / 50–60 °C | Bumpers, cases, seals |
| Bambu Lab ABS | ABS, 1.75 mm ±0.03 mm | 240–270 °C / 80–100 °C | Enclosed printers, heat-resistant parts |
Bambu Lab PLA Basic
The obvious material for owners of a Bambu printer. According to the manufacturer, it works with all AMS variants, and the RFID chip transfers temperature and profile automatically. Bambu Lab specifies print speeds of up to 300 mm/s. It works just as well on other printers, only without the convenience of the chip.
Polymaker PolyTerra PLA
A PLA based on bioplastic that, according to the data sheet, can be printed at between 50 and 300 mm/s. The values are close to PLA Basic, and the heat deflection temperature is even slightly lower. If you do not have a Bambu printer, you lose nothing with this spool.
Extrudr PLA NX2 Matt
Extrudr manufactures in Austria and describes NX2 as a more impact-resistant PLA with a matte surface and improved UV resistance. The data sheet recommends 20 to 200 mm/s and states a shelf life of two years when stored dry. In addition to 1 kg, there are spools of 2.5 and 10 kg, interesting for heavy users.
Prusament PETG
Prusa Polymers produces the filament in Prague, and according to Prusa, it uses it to print parts for its own printers. The tolerance of ±0.02 mm can be checked via the QR code on your own spool. For functional parts, this is our first choice among the filaments listed here.
Sunlu TPU 95A
Sunlu scales the temperature by speed: 190 to 210 °C at 50 to 80 mm/s, 210 to 230 °C at 80 to 120 mm/s. We would treat it the way Bambu Lab treats its own TPU 95A HF. In other words, feed it from an external spool, not through a multicolor system.
Bambu Lab ABS
According to Bambu Lab, it has been tuned for less warping. Without an enclosed printer and a ventilation plan, we still advise against it, because for almost everything that gets warm in the household, PETG is enough.
How we would shop
- Bambu printer with AMS: Bambu Lab PLA Basic, later ideally as a refill without a spool.
- Other printer, first spools: Polymaker PolyTerra PLA or, for matte parts, Extrudr PLA NX2 Matt.
- Holders, clips, parts for the balcony and garden: Prusament PETG.
- Flexible parts: Sunlu TPU 95A, fed from outside.
- Heat-resistant parts in an enclosed printer with ventilation: Bambu Lab ABS. Which printers are suitable for this is covered in our 3D printer guide.
What each color change costs in filament and time is calculated in the guide to multicolor 3D printing.
Frequently asked questions
Does every filament fit every 3D printer?
No, the diameter comes first. 1.75 and 2.85 millimeters are not interchangeable; which one fits is stated in the printer's data sheet. After that, tolerance matters: a strand of 1.80 instead of 1.75 mm pushes around six percent more plastic through the nozzle, and you can see that in the walls and dimensional accuracy.
What is the difference between PLA and PETG?
PLA prints at 190 to 230 °C, gets by with a lukewarm bed and suits figures, organizers and prototypes. Its limit is heat: Bambu Lab specifies a heat deflection temperature of 54 °C for PLA Basic. PETG closes that gap, and Prusa specifies 68 °C. As weaknesses, Prusa names stringing and very strong adhesion to the build plate.
Does filament need to be dried?
Often, yes, and sooner than many people think. Bambu Lab recommends 50 °C for eight hours for PLA Basic and 80 °C for eight hours for ABS. According to Bambu Lab, it should be stored below 20 percent humidity, sealed and with desiccant. Mind the spool: a Bambu Lab PLA spool is only rated up to 70 °C.
Are the fumes from 3D printing dangerous?
The Institute for Occupational Safety and Health of the German Social Accident Insurance (IFA/DGUV) measured volatile compounds at least an order of magnitude below the guideline values for PLA, PET, flexible filament, nylon and PE. ABS was the exception: styrene was in the same order of magnitude as the indoor guideline value. So run the printer in a separate room if possible and ventilate. ABS does not belong in a child's room.
Can TPU be printed in a multicolor system?
Not every system can handle such soft material. Bambu Lab itself declares its TPU 95A HF unsuitable for the AMS and offers a harder TPU for AMS instead. A soft TPU such as Sunlu TPU 95A is therefore fed from an external spool, not through a multicolor system.
When do you need ABS filament?
For heat-resistant parts; Bambu Lab specifies a heat deflection temperature of 84 °C for its ABS. In return, it needs 240 to 270 °C at the nozzle, 80 to 100 °C on the bed and an enclosed printer, because it warps easily. Without a ventilation plan, we advise against it; for almost everything that gets warm in the household, PETG is enough.
Sources
- Bambu Lab: PLA Basic technical data sheet
- Bambu Lab: PLA Basic
- Bambu Lab: ABS technical data sheet
- Bambu Lab: ABS
- Bambu Lab: TPU 95A HF
- Bambu Lab: TPU for AMS
- Polymaker: PolyTerra PLA technical data sheet V6.0
- Extrudr: PLA NX2 Matt technical data sheet
- Extrudr: PLA NX2 Matt
- Prusa Polymers: Prusament PETG technical data sheet
- Prusament: PETG
- Prusament: spool data via QR code
- Sunlu: TPU 95A
- IFA/DGUV: emissions from desktop 3D printers, Gefahrstoffe 80 (2020)
- DGUV Information 202-103 (German Social Accident Insurance): desktop 3D printers in schools
Where to buy
- Bambu Lab PLA BasicCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Polymaker PolyTerra PLACheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Extrudr PLA NX2 MattCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Prusament PETGCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Sunlu TPU 95ACheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Bambu Lab ABSCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
