Contents8 sections
This guide was first published in German on handgetestet.de.
The number on the box is almost never the number you will work with. If it says „up to 15 mm,“ the manufacturer usually means the severance cut: the sheet falls apart, and the edge then needs an angle grinder. If you mainly cut body panels and profiles up to 6 mm and already have a compressor delivering 100 liters per minute in the garage, a 40 to 50 amp machine with non-contact ignition will serve you well. Our favorite for this case is the Stahlwerk CUT 50 P Digital.
If you do not have compressed air in your workshop, you need a machine with a built-in compressor. It cuts thinner material and weighs more. A fair trade? For many people, yes.
Five numbers that count before you buy
For cutting thickness, it pays to look at the data sheet rather than the packaging. Güde separates the figures clearly: for the GPS-E 40 A.3, the manufacturer specifies 0 to 6 mm for the precision cut and 6 to 12 mm for the severance cut. For the Powermax30 AIR, Hypertherm recommends 8 mm at 500 mm per minute; it severs up to 16 mm, but then at only 125 mm per minute. Rule of thumb from these figures: the clean edge ends at roughly half the maximum value.
Compressed air matters more than amperage when choosing a machine. Stahlwerk requires at least 100 liters per minute at 4 bar for the CUT 50 models, and Güde even 150 liters per minute at 3 to 6 bar for the GPS-E 40 A.3. This means air that actually arrives at the machine. More on this in our workshop compressor guide (in German). Hypertherm lists moisture in the nozzle and electrode as a possible cause of ignition problems, which is why Stahlwerk and Güde include water separators in the box and Telwin offers its own moisture filter as an accessory. Machines with a built-in compressor do without a hose but deliver less air: for the AirCut 40 AK, Güde specifies 80 liters per minute at 2 bar.
There are three approaches to ignition. High-frequency ignition (Stahlwerk CUT 50 P, both Güde models) starts the arc without contact. The blowback ignition of the CUT 50 P Digital does this too, just without high frequency, and it is precisely this version that Stahlwerk has equipped with an interface for CNC tables. On the Infinity Plasma 40, Telwin uses contact ignition, so the nozzle briefly touches down. That is enough for smooth sheet metal. For grating and expanded metal, a pilot arc that stays lit through interruptions helps; Hypertherm explicitly mentions this feature for grating and rusty material.
The duty cycle is often overlooked. Stahlwerk specifies 15 percent at 45 A for the CUT 50 P and 30 percent at 50 A for the Digital model, each at 40 °C. The value refers to ten minutes: 30 percent means three minutes of cutting, seven minutes of rest.
That leaves the power connection. Güde and Telwin specify a 16 A fuse, Güde explicitly a slow-blow one. Hypertherm lays out the math openly: at 230 V with 16 A, the Powermax30 AIR delivers at most 28 A, and the full 30 A is only available on a 20 A circuit. And according to the manual, the European version comes without a plug. A qualified electrician fits it.
Six machines side by side
| Model | Air | Cut according to the manufacturer | Ignition, duty cycle | Best for |
|---|---|---|---|---|
| Stahlwerk CUT 50 P Digital | external, min. 100 l/min, max. 4 bar | mild steel up to 20 mm | Blowback without HF, 30% at 50 A | Workshop with compressor, CNC plans |
| Stahlwerk CUT 50 P | external, min. 100 l/min, 4 bar | mild steel up to 15 mm | HF pilot, 15% at 45 A | Hobby metalwork with compressor |
| Güde GPS-E 40 A.3 | external, min. 150 l/min, 3–6 bar | clean 0–6 mm, severance cut 6–12 mm | High frequency, 20% at 40 A | Sheet metal and occasional cuts |
| Telwin Infinity Plasma 40 | external, 100 l/min, 4–5 bar | up to 15 mm | Contact ignition, 20% at 40 A | Bodywork, lightweight machine |
| Güde GPS-K AirCut 40 AK | built-in, 80 l/min, 2 bar | clean 0–6 mm, severance cut 6–12 mm | High frequency, 30% at 40 A | Hobby use without compressed air |
| Hypertherm Powermax30 AIR | built-in | recommended 8 mm, severance cut 16 mm | Continuous pilot arc, 35% at 240 V | Mobile professional use |
You cut bodywork and thin sheet metal
Fenders, rocker panels, floor panels: here it is about 0.8 to 3 mm and clean edges that can still be welded. For that, 40 A is enough.
Telwin Infinity Plasma 40
Telwin specifies 7.4 kg and a control range of 10 to 40 A; a pressure regulator and a 4 m torch are included. An indicator shows when the nozzle and electrode are worn. Contact ignition is hardly a nuisance on smooth sheet metal. If you often cut grating, Hypertherm is the better place to look.
Güde GPS-E 40 A.3
Güde explicitly targets this machine at home and hobby DIYers. According to listings on Amazon, it sits in the lower price range, and it weighs 6.2 kg. Its air requirement of 150 liters per minute, however, is high. A small compressor with a delivery rate of 100 liters does not meet this specification. The duty cycle of 20 percent at full current is enough for repairs, not for production work.
Hobby metalwork without compressed air
Garden gate, grill frame, brackets made of flat steel. If you lack a large compressor, that leaves machines with a built-in compressor. They are heavier than you might think.
Güde GPS-K AirCut 40 AK
Plug it in and start cutting: that is the appeal. Güde specifies the same cutting ranges as for the sister model without a compressor, so 0 to 6 mm clean and up to 12 mm as a severance cut, plus a 30 percent duty cycle at 40 A. At 20.3 kg net, however, it is not a machine for the ladder.
Hypertherm Powermax30 AIR
Hypertherm classifies it as a professional machine: built-in compressor, 9.5 kg including a 4.5 m torch. According to listings on Amazon, it sits in the upper price range, and Hypertherm gives a six-year warranty on the power supply. Two quirks are noted in the manual: moisture from the compressor escapes underneath the machine, and a small puddle can form. And according to the manufacturer, the consumables last about one to two hours of pure arc time. For a hobby basement, that is a lot of machine. For installation work, agriculture or jobs without compressed air, it is the solid choice.
Workshop with compressor
If a compressor with sufficient delivery rate is available, the weight of a built-in compressor falls away. The machines get smaller and, according to the data sheets, cut thicker material.
Stahlwerk CUT 50 P Digital
Our favorite for this case. Stahlwerk specifies 15 to 50 A, mild steel up to 20 mm and a 30 percent duty cycle at 50 A. The blowback ignition starts without workpiece contact and without high frequency, and the THC interface allows it to be mounted on a CNC table later. You should not set the pressure above 4 bar; otherwise, according to Stahlwerk, ignition can falter. For the weight, the manufacturer gives two figures, 9 and 9.5 kg.
Stahlwerk CUT 50 P
The simpler version with HF pilot ignition, 15 to 45 A and 5 kg. The scope of delivery includes a water separator, a 5 m air hose and two nozzles and two electrodes. The weak point is the duty cycle: 15 percent at 45 A. If you mostly cut at around 22 A, you get 60 percent, according to the manufacturer.
Protection for eyes, lungs and workshop
Glaring UV and IR light, sparks, glowing spatter, toxic gases: that is how the DGUV, the German Social Accident Insurance, describes the hazards of plasma cutting. In its safety manual for Europe, Hypertherm specifies shade 9 according to EN 168 for up to 125 A. In its publication for fire departments, the DGUV lists shades 9 to 13 according to DIN EN 169 (the German edition of the European standard) for welding filters used in plasma cutting, and points out that an auto-darkening filter must react sensitively enough to the cutting arc. Add gloves with long cuffs according to DIN EN 12477 and clothing that does not catch sparks.
The fumes are where it gets serious. According to the DGUV, handheld plasma cutting with compressed air produces high concentrations of gases such as carbon monoxide and nitrous gases, especially in poorly ventilated rooms. After substitution with lower-emission processes, the DGUV says the next priority is extraction directly at the source, and only then organizational measures and protective equipment. Hypertherm also advises removing paints and coatings before cutting; galvanized sheet metal and old paints containing lead or cadmium release toxic fumes.
On fire protection: Hypertherm requires a fire extinguisher within reach and nothing flammable within a 10 m radius. No cutting on containers that may have held flammable substances, and no barrel as a cutting table. If you have a pacemaker, Hypertherm says you should clear its use with a doctor beforehand. For deburring afterward, a cordless angle grinder (in German) is enough. If you then want to join the parts, you will find the right equipment in our welder guide.
How we would decide
- Compressor with at least 100 l/min available, sheet metal and profiles up to 6 mm: Stahlwerk CUT 50 P Digital.
- Body panels only, weight matters: Telwin Infinity Plasma 40.
- Small budget, few cuts a year and a powerful compressor: Güde GPS-E 40 A.3.
- No compressed air and no need for mobility: Güde GPS-K AirCut 40 AK.
- No compressed air, often on the move, high demands: Hypertherm Powermax30 AIR.
Factor in nozzles and electrodes right from the start. Hypertherm recommends always replacing both together; piercing in the middle of a sheet wears them out faster than a cut started from the edge.
Frequently asked questions
How thick does a plasma cutter really cut cleanly?
The figure on the box usually refers to the severance cut, after which the edge needs an angle grinder. For the GPS-E 40 A.3, Güde specifies 0 to 6 mm for the precision cut and 6 to 12 mm for the severance cut. As a rule of thumb, the clean edge ends at roughly half the maximum value.
Which compressor does a plasma cutter need?
Compressed air matters more than amperage. Stahlwerk requires at least 100 liters per minute at 4 bar for the CUT 50 models, and Güde even 150 liters per minute for the GPS-E 40 A.3. This means air that actually arrives at the machine. A water separator keeps moisture away from the nozzle and electrode.
What does the duty cycle on a plasma cutter mean?
The value refers to ten minutes: 30 percent means three minutes of cutting and seven minutes of rest. Stahlwerk specifies 15 percent at 45 A for the CUT 50 P and 30 percent at 50 A for the Digital model, each at 40 °C.
Which ignition is suitable for grating and expanded metal?
A pilot arc that stays lit through interruptions helps there; Hypertherm explicitly mentions this feature on the Powermax30 AIR for grating and rusty material. The contact ignition of the Telwin Infinity Plasma 40, where the nozzle briefly touches down, is enough for smooth sheet metal.
What protective equipment do you need for plasma cutting?
A welding filter (Hypertherm specifies shade 9 up to 125 A), plus gloves with long cuffs according to DIN EN 12477 and clothing that does not catch sparks. According to the German Social Accident Insurance (DGUV), extraction directly at the source takes priority. Keep a fire extinguisher within reach and nothing flammable within 10 m.
Can you run a plasma cutter on a normal outlet?
Güde and Telwin specify a 16 A fuse. Hypertherm calculates that at 230 V with 16 A, the Powermax30 AIR delivers at most 28 A, and the full 30 A only on a 20 A circuit. The European version comes without a plug; a qualified electrician fits it.
Sources
- Stahlwerk: CUT 50 P Digital plasma cutter
- Stahlwerk: CUT 50 P plasma cutter
- Güde: GPS-E 40 A.3 plasma cutter
- Güde: GPS-K AirCut 40 AK plasma cutter
- Telwin: Infinity Plasma 40
- Hypertherm: Powermax30 AIR
- Hypertherm: Powermax30 AIR, operator manual 808840 (PDF)
- Hypertherm: Safety and compliance manual 80669C (PDF)
- DGUV (German Social Accident Insurance): Fachbereich Aktuell FBFHB-013, protective measures when using plasma cutting equipment (PDF, March 2026, in German)
Where to buy
- Stahlwerk CUT 50 P DigitalCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Güde GPS-E 40 A.3Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Stahlwerk CUT 50 PCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Telwin Infinity Plasma 40Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Güde GPS-K AirCut 40 AKCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Hypertherm Powermax30 AIRCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
