Contents14 sections
This guide was first published in German on handgetestet.de.
22 megapixels, 4300 dpi, 25 megapixels. Slide scanners are advertised with figures like these, and that is exactly where many bad purchases begin. The numbers are often interpolated and say little about sharpness. For a lot of slides and negatives in good quality, there is hardly any way around a true film scanner with an infrared channel, such as the Plustek OpticFilm 8300i SE. The small devices with a screen are faster. But much coarser.
Which type of device suits whom
There are four ways to get from slide to file. Which one suits you depends on the quantity and on what you want to do with the pictures later.
Quick digitizers such as the Reflecta x22-Scan or the Kodak Scanza photograph the slide with a small camera sensor. It takes seconds and needs no computer. That is enough for sorting and for viewing on the TV, but not for large prints.
A true film scanner reads the image line by line, in Plustek’s case with a CCD sensor and an infrared channel against dust. Each frame takes half a minute to several minutes, and nothing works without a computer. In return, you get a file fit for an archive.
Flatbed scanners with a transparency unit read several slides at once, plus paper photos and larger film formats. They are hardly available new anymore.
That leaves a scanning service. It takes the work off your hands entirely, which pays off with very large collections or when the device would only sit in a cupboard afterward. The slides do have to leave your hands, though. And it takes time.
What a scanner really resolves
A 35 mm slide measures 36 × 24 millimeters. How much detail comes out of it is decided by the sensor, not by the number in the menu. Many inexpensive devices list two values in their data sheet. The Kodak Scanza, for example, lists a 14-megapixel sensor, while 22 megapixels are advertised. The second value is calculated. No new detail is created in the process.
Even the optical figure is only an upper limit. For the OpticFilm 8200i, Plustek states 7200 dpi. In its test of the 8200i, the specialist site filmscanner.info measured an effective resolution of about 3250 ppi, a little under half. On a 35 mm frame, that leaves around 14 megapixels of real information. Enough for large prints, and an honest yardstick that the competition has to measure up to.
That is why sensor size and native pixels count. According to its data sheet, the Reflecta x22-Scan uses an 8-megapixel sensor in the 1/4-inch format, smaller than in many smartphones.
Dust, scratches and the infrared channel
Good film scanners make a fourth pass with infrared light. It detects dust and scratches and retouches them automatically. Plustek calls this iSRD, Epson calls it Digital ICE. The method has limits: infrared detection does not work with traditional black-and-white film, because the silver in the film blocks the light. Epson also advises against using it with Kodachrome.
And the file format? Devices with a screen usually save only JPEG. For editing, you need a scanner with software on the computer and TIFF output.
Speed versus quality
This is where the real trade-off lies. How many slides do you have? According to Plustek, the 8200i Ai needs just under two minutes per frame at full resolution with multi-sampling, and around 36 seconds at 3600 dpi. With 2,000 slides, that adds up to many evenings. Devices with a camera sensor such as the Kodak Scanza capture in seconds but deliver visibly less.
True magazine scanners that work through an entire CS or LKM slide magazine unattended have almost disappeared from the market. According to filmscanner.info, the Reflecta DigitDia 7000 is no longer made, and its successor, the DigitDia evolution, was most recently listed by specialist retailers only with a long delivery time and plays in a completely different price league. The Plustek OpticFilm 135i offers a middle ground: according to the manufacturer, it scans a strip of six frames or four mounted slides in one pass.
A word on flatbed scanners. Epson now lists the well-known Perfection V600 Photo and V850 Pro models as „no longer available.“ Epson currently offers no new Perfection model with a transparency unit.
What independent tests say
Large comparison tests of slide scanners have become rare, and many are old. Here is what independent testers have checked, with date and result. The picture is thinner than the advertising suggests.
Stiftung Warentest: comparison from 2010, quick test from 2011
The most recent comparison by Stiftung Warentest, the German product-testing foundation, that we could find was published on February 25, 2010: „Digitizing pictures: bringing photos back to life“. It tested slide and flatbed scanners, a slide duplicator and, as examples, two scanning services. The flatbed scanners from Canon and Epson delivered the highest image quality. The slide scanners from Plustek and Reflecta produced „good“ images with optimized settings, and for large quantities the Reflecta magazine scanner was „hard to beat.“ On resolution, the test advised scanning slides at least at 1200 dpi, saying more than 4200 dpi brought little. Today’s models were not yet included.
On August 25, 2011, this was followed by a quick test of a slide scanner from a discount store that works on the camera principle. The verdict: image quality „passable,“ with weaknesses on high-contrast subjects. The sensor delivered around 1400 dpi, the advertised 2000 dpi were interpolated, and only a 22 × 29 millimeter section of the 35 mm frame remained. Today’s quick digitizers work on the same principle.
c’t Fotografie and heise Foto
The German photo magazine c’t Fotografie covered film scanners in issue 4/2020 („Digitizing analog film“, online since July 27, 2020). The article names resolution, density range, speed, features and scanning software as criteria. The individual results are reserved for subscribers and are therefore missing here.
Freely readable is a test by heise Foto dated August 18, 2014 of the Reflecta ProScan 10T. It shows the basic problem in numbers. Advertised with 10,000 sampling points per inch, the device resolved 3649 on the test chart. Its predecessor, the ProScan 7200, reached 2597 at a nominal 3600.
filmscanner.info: measured instead of advertised resolution
The specialist site filmscanner.info measures effective resolution with a test slide. It belongs to a film scanner retailer, which is worth knowing when reading it. For the OpticFilm 8200i, released in 2012, it arrived at about 3250 ppi at a nominal 7200, which in its assessment is enough for prints up to A4 size. The OpticFilm 135 from 2017, predecessor of the 135i and still without an infrared channel, reached about 3280 ppi at a nominal 3600. The site does not yet list reviews of the 8300i SE or the 135i.
Individual tests of the Plustek models
The Swiss magazine PCtipp tested the OpticFilm 8200i SE on March 26, 2015. The editors liked the hardware and the infrared correction, but not the bundled software. A full-resolution scan including preview took a good three minutes, and because the film is advanced by hand, the device was not suited to large series.
Digital Camera World tested the OpticFilm 8300i SE on November 5, 2023, and awarded it five out of five stars. At 7200 dpi with infrared, the tester clocked 2:21 minutes per frame, compared with 2:58 minutes for the predecessor 8200i SE. His verdict: same image quality, somewhat faster, no reason for owners of the predecessor to switch. He names 3600 dpi as a sensible setting.
fotoMAGAZIN
On February 14, 2026, the German photo magazine fotoMAGAZIN published an overview of digitizing and refers in it to its own test in issue 12/24. The Reflecta x44-Scan, a sister model of the x22-Scan with 16 megapixels, received a „very good“ rating there. That cannot be transferred to the x22-Scan with 8 megapixels. The overview lists the Plustek OpticFilm 8300i SE with manufacturer data, without a rating.
One pattern runs through all the measurements: the nominal resolution is never reached. When reading tests, the measured figure is what counts. Not the advertised one.
6 slide and negative scanners side by side
| Model | Scanning principle and sensor | Resolution according to manufacturer | Film formats | Several frames in one go | Dust and scratch correction | Connection and storage | Best for |
|---|---|---|---|---|---|---|---|
| Plustek OpticFilm 8300i SE | Film scanner, CCD line sensor, LED light | 7200 dpi, density 3.6 | 35 mm: mounted slides and film strips | no, frame by frame | yes, infrared (iSRD) | USB 2.0, computer required | Demanding archive work, mid-range |
| Plustek OpticFilm 8200i Ai | Film scanner, CCD line sensor, LED light | 7200 dpi, density 3.6 | 35 mm: mounted slides and film strips | no, frame by frame | yes, infrared (iSRD) | USB 2.0, computer required, SilverFast Ai Studio with IT8 target | Color accuracy and fine work |
| Plustek OpticFilm 135i | Film scanner, CCD line sensor, LED light, automatic batch scanning | 7200 dpi, density 3.4 | 35 mm, panorama up to 226 mm with optional holder | yes, four slides or six frames of a strip | yes, infrared | USB 2.0, computer required | Larger collections, less manual work |
| Reflecta x22-Scan | Camera sensor, 1/4-inch CMOS, 8 megapixels | 3468 × 2312 pixels, 4904 × 3268 interpolated | 35 mm: mounted slides and film strips | no, holder for four slides or six frames | no | SD card up to 128 GB, USB 2.0, no computer required | Quick sorting, entry level |
| Kodak Scanza | Camera sensor, 14 megapixels | 14 megapixels, 22 interpolated | 35 mm, 126, 110, Super 8 and 8 mm | no, adapter for each format | no | SD card, USB, video output, HDMI cable included | Mixed old collections, quick copies |
| Nikon ES-2 (camera adapter) | Attachment for Nikon macro lenses, camera’s sensor | depends on camera | Negatives and slides in holder | no, frame by frame | no | Camera’s memory card | Owners of a suitable Nikon camera |
All values are manufacturer specifications as of November 2026; the data sheets are listed under Sources. The 7200 dpi of the Plustek devices are nominal values. How much of that reaches the image is shown by the measurements in the previous section.
Plustek OpticFilm 8300i SE
The successor to the well-known 8200i SE. Plustek sticks to the principle: CCD line sensor, LED light, 7200 dpi and an infrared channel for iSRD, plus SilverFast SE Plus 9 and QuickScan Plus. According to the manufacturer, newer algorithms speed up scanning by up to 38 percent. Specifically, the data sheet gives about 20 seconds per frame at 3600 dpi, 40 seconds with infrared, and around two minutes at 7200 dpi with infrared. We do not yet know of an independent measurement of the effective resolution for the new model; for its predecessor, filmscanner.info arrived at about 3250 ppi. It is not fast either. In return, you get a file that will still hold up in twenty years.
Plustek OpticFilm 8200i Ai
Still the older 8200i hardware, but with the bigger software package. According to Plustek, SilverFast Ai Studio adds multi-exposure for more dynamic range and automatic IT8 color calibration, with the target included. That helps with dense slides with deep shadows. If you are only preserving family negatives, you can do without the extra cost.
Plustek OpticFilm 135i
The 135i takes an entire strip of six frames or four slides and recognizes the film type from the holder, as Plustek describes it. Panorama formats up to 226 millimeters wide are also possible with an optional holder. With collections in the thousands, that noticeably cuts down on handling. The pass is still not fast: for the full scan area with infrared, Plustek quotes around six minutes at 3600 dpi and about 25 minutes at 7200 dpi. It does cost more than the 8200i SE, though.
Reflecta x22-Scan
A small device with a 5.8-centimeter screen that saves directly to an SD card. The sensor natively delivers 3468 × 2312 pixels; the larger output is interpolated. Buyers praise the speed but criticize color casts and limited contrast range with color negatives. That is enough for sorting and sharing. Not for an archive.
Kodak Scanza
According to its manual, the Scanza uses a 14-megapixel sensor; the 22 megapixels are interpolated. Its advantage is the range of formats: 35 mm, 126, 110 as well as Super 8 and 8 mm film strips, plus a tilting screen and HDMI output. Some buyers report that especially thick slide mounts do not fit in the holder.
Nikon ES-2: digitizing with a camera
The adapter screws onto the front of a macro lens, the slide sits in the holder in front of it, and each shot takes seconds. Nikon lists the AF-S DX Micro Nikkor 40 mm, the 60 mm Micro Nikkors and the Nikkor Z MC 50 mm as suitable lenses. Automatic negative inversion only works on Nikon cameras with a digitizing menu; with a D850 and a 60 mm lens, according to Nikon, the result is good enough for prints up to A1 size. There is no infrared, so dust has to be removed beforehand or retouched later. If you still need a suitable camera, our overview of mirrorless cameras (in German) will help.
Super 8 films need a dedicated device
Super 8 is often mentioned alongside slides. But it is moving film. According to its data sheet, the Kodak Scanza accepts Super 8 and 8 mm strips but saves individual JPEG images, so you do not end up with a film.
For that there are small-gauge film scanners such as the Reflecta Film Scanner Super 8 – Normal 8. According to Reflecta, it scans the film frame by frame at two frames per second, so a 15-meter reel takes around 30 minutes. The sensor has 3.53 megapixels. Output is saved as MP4 at 1440 × 1080 pixels directly to an SD card of up to 32 gigabytes, with no computer required. The manufacturer itself names two limits: reels up to 12.7 centimeters in diameter and no sound recording. Sound films stay silent.
How we would decide
For a family archive in good quality, we would choose the Plustek OpticFilm 8300i SE. Slow, but with real resolution and dust removal. For critical slides where color accuracy matters, the 8200i Ai with calibration makes more sense; for lots of film strips and little time, the OpticFilm 135i.
The Reflecta x22-Scan and Kodak Scanza are fine for sorting and for showing on the TV. For prints or a permanent archive, we would advise against them. If you already have a Nikon camera with a macro lens in the cupboard, the ES-2 is the fastest route to high resolution, but it requires careful work.
A TIFF scan at 7200 dpi quickly takes up more than a hundred megabytes. So plan your storage in advance, for example with an external SSD (in German) as a working drive and a backup on a NAS (in German). One more thing about the content. Slides often show other people, and if you share the pictures online later, you should ask the people in them first.
For presorting the mounts, a light panel is often enough; see our guide to light pads (in German). For old video tapes, there is our guide Digitizing VHS.
Paper photos, albums and slides together are covered in our guide Digitizing photos (in German), with time estimates and scanning services.
Frequently asked questions
How much resolution does a slide scanner really deliver?
Advertised figures are often interpolated. The Kodak Scanza's data sheet lists a 14-megapixel sensor, while 22 megapixels are advertised. Even the optical figure is an upper limit: for the OpticFilm 8200i rated at 7200 dpi, filmscanner.info measured an effective resolution of about 3250 ppi.
What does the infrared channel do when scanning slides?
Good film scanners make a fourth pass with infrared light that detects dust and scratches and retouches them automatically; Plustek calls it iSRD, Epson calls it Digital ICE. It does not work with traditional black-and-white film, because the silver in the film blocks the light. Epson also advises against it for Kodachrome.
How long does it take to scan a slide?
According to Plustek, the 8200i Ai needs just under two minutes per frame at full resolution with multi-sampling, and around 36 seconds at 3600 dpi. According to the manufacturer, the 8300i SE is up to 38 percent faster. Devices with a camera sensor capture in seconds but deliver visibly less.
Which scanner suits large slide collections?
According to the manufacturer, the Plustek OpticFilm 135i scans a strip of six frames or four mounted slides in one pass and recognizes the film type from the holder. With collections in the thousands, that noticeably cuts down on handling. True magazine-fed slide scanners have almost disappeared from the market.
Can you digitize slides with a camera?
With the Nikon ES-2 you can: the adapter sits in front of a macro lens, and each shot takes seconds. With a D850 and a 60 mm lens, according to Nikon, the result is good enough for prints up to A1 size. There is no infrared, so dust has to be removed beforehand or retouched later.
JPEG or TIFF when scanning slides?
Devices with a built-in screen usually save only JPEG. For editing, you need a scanner with computer software and TIFF output. A TIFF scan at 7200 dpi quickly takes up more than a hundred megabytes, so plan storage such as an external SSD and a backup in advance.
Digitizing slides: scanner or service?
Your own film scanner is worth it if you have the time and do not want the pictures to leave your hands. A service saves you the equipment and the work, but the slides travel by mail and it takes time. In 2010, Stiftung Warentest, the German product-testing foundation, checked two providers as examples and found the quality solid. With thousands of slides, a preselection helps.
Is there a current slide scanner test from Stiftung Warentest?
The most recent Stiftung Warentest comparison we could find was published on February 25, 2010, followed by a quick test of a discount-store device in August 2011. Today's models such as the Plustek OpticFilm 8300i SE were not included. More recent individual tests come from trade magazines, such as Digital Camera World (2023) and the German photo magazine fotoMAGAZIN (issue 12/24).
Can a slide scanner also digitize Super 8 films?
Only to a limited extent. Devices such as the Kodak Scanza accept Super 8 strips but save individual frames as JPEG. For moving film there are dedicated small-gauge film scanners: according to the manufacturer, the Reflecta Film Scanner Super 8 – Normal 8 saves MP4 files to an SD card, needs about 30 minutes for 15 meters of film and does not record sound.
Sources
- Plustek: OpticFilm 8200i Ai
- Plustek: OpticFilm 8200i Ai data sheet
- Plustek: OpticFilm 8300i SE
- Plustek: OpticFilm 8300i SE specifications
- Plustek: OpticFilm 135i
- filmscanner.info: Plustek OpticFilm 8200i test (effective resolution)
- filmscanner.info: Reflecta DigitDia 7000
- Calumet: Reflecta x22-Scan data sheet
- Kodak Scanza: user manual
- Epson: Perfection V850 Pro (Digital ICE, status)
- Epson: Perfection V600 Photo (status)
- Nikon: ES-2 film digitizing adapter
- Stiftung Warentest: Digitizing pictures, bringing photos back to life (25.02.2010)
- Stiftung Warentest: quick test of a slide scanner from Norma, a German discount supermarket (25.08.2011)
- c’t Fotografie 4/2020: Digitizing analog film (27.07.2020)
- heise Foto: Reflecta 10T film scanner (18.08.2014)
- filmscanner.info: Plustek OpticFilm 135 test
- filmscanner.info: overview of test reports
- PCtipp: Plustek OpticFilm 8200i SE test (26.03.2015)
- Digital Camera World: Plustek OpticFilm 8300i SE review (05.11.2023)
- fotoMAGAZIN: Digitizing photos with a camera and scanner (14.02.2026)
- Plustek: OpticFilm 135i specifications
- Reflecta: x22-Scan (technical data)
- Kodak Scanza: data sheet
- Reflecta: Film Scanner Super 8 – Normal 8
Where to buy
- Plustek OpticFilm 8300i SECheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Plustek OpticFilm 8200i AiCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Plustek OpticFilm 135iCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Reflecta x22-ScanCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Kodak Scanza (RODFS35)Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Nikon ES-2Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
