Contents11 sections
This guide was first published in German on handgetestet.de.
An impact wrench for changing tires has to do one thing above all: loosen rusted-on lug nuts. When tightening, on the other hand, it should stop early. That’s why breakaway torque matters more than the big number on the box when you buy, and a low first setting is more important than the third. For car wheels in your own garage, we consider the Makita DTW700 the balanced choice, because it offers both.
A quick calculation shows why. According to Einhell, car wheel bolts are usually tightened to 80 to 160 Nm; the exact figure is in the vehicle’s owner’s manual. Even the weakest setting of most tools here is above that. So an impact wrench with 1,000 Nm of tightening torque doesn’t tighten a lug nut better. It only tightens it harder.
Breakaway torque, settings, sockets: what really counts when changing wheels
Manufacturers list two figures. Tightening torque describes how hard the tool tightens a fastener. Breakaway torque, also called nut-busting torque, indicates the resistance it can overcome when loosening. After a winter of road salt, this second figure decides whether the nut comes off or not. For car wheels, even 800 Nm gives you plenty of headroom over the tightening value; you need more if you look after vans, trailers or farm machinery.
The settings are the second point. A good tool has a lowest setting that stays close to the target value, or it shuts off on its own when tightening. Then the wrench runs the nut on quickly without overtightening it. Either way, the final pull is done with a torque wrench. In the manual for the GDS 18V-1000, Bosch explicitly states that the tightening torque actually achieved must always be checked with a torque wrench. Which models are suitable is covered in our guide to torque wrenches (in German).
That leaves the socket. An impact wrench’s square drive takes impact-rated sockets, not hand sockets from a ratchet set. Bosch requires this in its safety instructions too: only impact-rated sockets, because only these are suitable for impact wrenches. For alloy wheels, there are sockets with a plastic sleeve designed to protect the edge of the lug hole. According to Bosch, an extension makes the joint more elastic; the achievable torque drops and the impact time increases. If you’re planning to buy a set anyway, you’ll find tips in our guide to socket sets.
The square drive itself comes in two designs. With a hog ring, a ring holds the socket by friction, and changing sockets is quick. With a detent, a spring-loaded ball or pin locks into the socket. Both work with standard 1/2-inch impact sockets.
Battery platform first, then the tool
An impact wrench draws a lot of current in short bursts. For the full performance of the GDS 18V-1000, Bosch specifies a ProCORE18V battery of 5.5 Ah or more; Einhell recommends at least 2.5 Ah for the IMPAXXO 18/450. If you already have batteries from one brand on the shelf, buy the bare tool and save yourself another charger. How the platforms differ is explained in our guide to cordless battery systems. Switching brands just for the impact wrench is, in our view, the wrong approach.
Five 1/2-inch impact wrenches side by side
| Model | Tightening / breakaway (manufacturer specs) | Settings | Best for |
|---|---|---|---|
| Makita DTW700 | 700 Nm / 1,000 Nm | 4 settings from 150 Nm, auto-stop | Car wheels, home workshop |
| Einhell IMPAXXO 18/450 | 450 Nm / 800 Nm | 3 speeds from 200 Nm | Seasonal changes, Power X-Change owners |
| DeWalt DCF892 | 813 Nm / nearly 1,100 Nm | 4 settings, one control setting | Tight wheel wells, assembly work |
| Bosch Professional GDS 18V-1000 | 1,000 Nm / 1,600 Nm | 3 settings from 350 Nm | Vans, trailers, job sites |
| Milwaukee M18 FHIW2F12 | 1,491 Nm / 2,034 Nm | 4 settings, bolt-removal mode | Trucks, farm equipment, steel construction |
Makita DTW700
Makita specifies four settings of 150, 200, 320 and 700 Nm, and the breakaway torque is 1,000 Nm. There’s also a three-stage auto-stop for forward and reverse, which the manufacturer explicitly mentions for changing tires. At 170 mm long and 2.0 kg without the battery, the tool stays easy to handle. The 150 Nm setting is close to typical wheel-bolt values, and that’s exactly why the DTW700 comes first for us.
Einhell IMPAXXO 18/450
Einhell specifies 450 Nm of tightening torque and 800 Nm of breakaway torque, spread across three speeds of 200, 280 and 450 Nm. A socket set for changing tires is already in the box. The tool weighs 1.99 kg. For swapping between summer and winter wheels twice a year, that’s enough. For seized nuts on a trailer, the margin is tighter.
DeWalt DCF892
At 175 mm overall length, the DCF892 is short. DeWalt specifies over 800 Nm when tightening and a breakaway torque of nearly 1,100 Nm. The fourth setting is a control setting that stops forward rotation as soon as the bolt seats; that helps when running nuts on. The socket is held by a detent pin, and the impact mechanism sits in an aluminum housing.
Bosch Professional GDS 18V-1000
Bosch specifies 1,000 Nm of tightening torque and 1,600 Nm of breakaway torque, in three settings of 350, 700 and 1,000 Nm. The anvil has a hog ring. It weighs 2.9 kg without the battery, and according to the manufacturer, full performance is only available with large ProCORE batteries. For car wheels, that’s more tool than you need. If you maintain vans or trailers, though, you get plenty of reserve for loosening.
Milwaukee M18 FHIW2F12
This is a different league. Milwaukee specifies 1,491 Nm of fastening torque and 2,034 Nm of breakaway torque at a length of 193 mm. The fourth mode loosens nuts at full torque and then drops back to 750 rpm. For the family car, that’s clearly oversized. In a truck or farm-equipment workshop, it makes sense.
Noise, vibration and the right procedure
Impact wrenches are loud. Makita states a sound pressure level of 97 dB(A) for the DTW700, and Bosch 93.5 dB(A) for the GDS 18V-1000, adding: wear hearing protection. For context: the German noise and vibration occupational safety ordinance (LärmVibrationsArbSchV) sets the lower action value at 80 dB(A) and the upper one at 85 dB(A), each based on an eight-hour workday. For hand-arm vibration, it sets 2.5 m/s² as the action value and 5 m/s² as the limit value. Makita states 19.0 m/s² for tightening at maximum load. If you change wheels every day for work, you should know these numbers.
For fitting wheels, the German automobile club ADAC advises: tighten lug nuts in a crisscross pattern to the specified torque, never lubricate the threads and check the fastening again after about 50 km. So the impact wrench only runs the nuts on, using the lowest setting or auto-stop. Then comes the torque wrench. In its manual, Bosch also explains why holding the trigger longer doesn’t help: maximum torque is reached after six to ten seconds of impacting, and after that it only rises minimally.
Which impact wrench suits which garage
- Car wheels in your own garage: Makita DTW700. Low first setting, auto-stop, 1,000 Nm for loosening.
- Two wheel changes a year and Einhell batteries already on hand: IMPAXXO 18/450, socket set included.
- Little room in the wheel well or assembly work: DeWalt DCF892 at 175 mm long.
- Vans, camper trailers, trailers: Bosch GDS 18V-1000, provided you have large batteries.
- Commercial vehicles and heavy-duty fasteners: Milwaukee M18 FHIW2F12.
Our take is simple. Buy based on breakaway torque and the lowest setting, not the maximum figure. And keep the torque wrench right next to it.
Frequently asked questions
How much torque does an impact wrench need for lug nuts?
According to Einhell, car wheel bolts are usually tightened to 80 to 160 Nm. What matters is the breakaway torque for rusted-on nuts. For car wheels, even 800 Nm gives you plenty of headroom; you need more if you look after vans, trailers or farm machinery.
What is the difference between tightening torque and breakaway torque?
Tightening torque describes how hard the tool tightens a fastener. Breakaway torque, also called nut-busting torque, indicates the resistance it can overcome when loosening. After a winter of road salt, this second figure decides whether the nut comes off or not.
Can I tighten lug nuts with an impact wrench?
Only run them on, using the lowest setting or auto-stop. The final pull is done with a torque wrench; Bosch also requires this in the manual for the GDS 18V-1000. The German automobile club ADAC advises tightening in a crisscross pattern, not lubricating the threads and checking again after about 50 km.
Which sockets do I need for an impact wrench?
Impact-rated sockets, not hand sockets from a ratchet set; Bosch requires this in its safety instructions. For alloy wheels, there are sockets with a plastic sleeve designed to protect the edge of the lug hole. According to Bosch, an extension reduces the achievable torque.
Which impact wrench fits two wheel changes a year?
If you already own Einhell batteries, the IMPAXXO 18/450 serves you well: 800 Nm breakaway torque, three speeds starting at 200 Nm and a socket set in the box. For seized nuts on a trailer, the margin is tighter. Switching brands just for the impact wrench is, in our view, the wrong approach.
Do I need hearing protection with an impact wrench?
Yes. Makita states a sound pressure level of 97 dB(A) for the DTW700, and Bosch 93.5 dB(A) for the GDS 18V-1000, explicitly adding: wear hearing protection. The German noise and vibration occupational safety ordinance sets the lower action value at 80 dB(A), based on an eight-hour workday.
Sources
- Makita: DTW700 cordless impact wrench, specifications
- Einhell: IMPAXXO 18/450, specifications
- DeWalt: DCF892NT 18V XR cordless impact wrench
- Bosch Professional: GDS 18V-1000, specifications
- Bosch Professional: GDS 18V-1000 operating manual (PDF)
- Milwaukee: M18 FHIW2F12
- Einhell: tips for changing tires (in German)
- ADAC: changing tires or wheels yourself (in German)
- LärmVibrationsArbSchV § 6: noise action values (German ordinance)
- LärmVibrationsArbSchV § 9: vibration values (German ordinance)
Where to buy
- Makita DTW700 (DTW700Z, ohne Akku)Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Einhell IMPAXXO 18/450 (ohne Akku)Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- DeWalt DCF892Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Bosch Professional GDS 18V-1000Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Milwaukee M18 FHIW2F12Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
