Contents12 sections
This guide was first published in German on handgetestet.de.
An LED strip rarely becomes a nuisance because of the LEDs. Usually it is the wrong power supply, a strip without a profile showing visible light dots, or controls that do not fit the rest of the home. For task lighting in the kitchen and workshop, we consider a bright 24-volt strip with a color rendering index of Ra 90 the solid choice, such as the Beneito FINE-69 from ELV (German retailer). For mood lighting, lumens matter less than good controls.
Before you decide on a model, it is worth looking at where it will go. Almost everything else follows from that.
Five numbers that appear on every good data sheet
Voltage. Most strips run on 12 or 24 volts DC. At the same power, only half the current flows at 24 volts: 28.8 watts is 2.4 amps at 12 volts and 1.2 amps at 24 volts. Less current means less loss on the thin conductor tracks, so the end of a long strip is more likely to stay as bright as the beginning. That is why all Beneito strips in this overview work with 24 volts.
Lumens per meter. This number decides whether a strip actually lights something or merely decorates. According to ELV, the FINE-69 delivers 940 lumens per meter in warm white, the more economical FINE-84 around 456. Between the two lies roughly the difference between a countertop and a ceiling cove.
Color rendering (Ra or CRI). The index describes how natural colors look under the light; 100 is the maximum. Ra 80 is enough for accent lighting. When chopping vegetables or soldering, Ra 90 makes a noticeable difference, because reds and skin tones do not look washed out. According to the data sheet, the Beneito strips reach more than 90, according to Philips the Hue Lightstrip more than 80, and according to ELV the tint outdoor strip 80.
You need watts per meter for the power supply, and the IP protection rating for bathrooms and outdoor areas. IP20 means: for dry indoor rooms only.
Sizing the power supply without guessing
The math is simple: watts per meter times length, then headroom. An example with 3 meters of FINE-69 under the wall cabinets comes to 3 × 9.6 W = 28.8 W. The power supply manufacturer Mean Well advises loading ordinary switching power supplies to only about 70 percent in most cases. 28.8 W divided by 0.7 gives just over 41 W. So a 24-volt power supply with 50 watts fits. According to Mean Well, dedicated LED drivers may also run at full load, as long as the case temperature stated in the data sheet is maintained. In a cramped cabinet cavity, we would not bet on that.
Two finer points. With RGB and RGBW strips, the wattage refers to all color channels at once, as the manufacturer eQ-3 explains at ELV; in practice, all of them rarely run at the same time. And the power supply must deliver safety extra-low voltage (SELV) for LED modules and be short-circuit-proof, as the manual of the Homematic IP LED Controller requires.
Which strip for which spot?
Our decision path runs through five typical uses. The key data are in the table, with the reasoning below.
| Model | Light and power | Ra and protection rating | For whom |
|---|---|---|---|
| Beneito FINE-69 3000 K IP20 | 940 lm/m, 9.6 W/m, 24 V | Ra 90, IP20 | Kitchen, task lighting |
| Beneito FINE-84 4000 K IP65 | 456 lm/m, 4.8 W/m, 24 V | Ra 90, IP65 | Indirect light, bathroom, covered outdoor areas |
| Homematic IP Lightstrip Set HmIP-LSS | 2 m, 12 W/m, 24 V, power supply included | Colors and white, IP20 | Homematic IP households |
| Philips Hue Lightstrip Plus V4 | 2 m, up to 1,700 lm, 20 W | CRI above 80, IP20 | Hue system, living room |
| Govee COB Strip Light Pro | 5 m, 450 lm/m, 72 W, 24 V | not specified, indoors | Dot-free light without a profile, Matter |
| tint Outdoor Lightstrip | 5 m, 1,200 lm, 36 W | Ra 80, IP44 | Garden and patio with Zigbee |
| Diamex WS2812 LED strip | 4 m, 60 LEDs/m, 5 V | IP20 | Tinkerers with a microcontroller |
Kitchen and workbench: Beneito FINE-69 3000 K IP20
Our main recommendation for task lighting. According to ELV, the strip has 140 LEDs per meter, 940 lumens per meter and Ra 90, and it can be cut every 50 millimeters. Beneito gives a five-year manufacturer’s warranty. There are drawbacks all the same: the power supply and dimmer are not included, and without a profile you can see the individual light dots on glossy countertops. If you would rather mount a ready-made light with a sensor, you will find alternatives in the guide to under-cabinet lighting for the kitchen.
An aluminum profile belongs with it. The P2-1 profile from ELV takes strips up to 12 millimeters wide, the matte cover diffuses the light, and one end cap has a cable entry. The aluminum also absorbs heat, which Beneito explicitly points out. According to the manual, soldering should take no more than five seconds at a maximum of 250 °C; an adjustable station from the soldering station guide (in German) makes that easier.
Indirect light and bathroom: Beneito FINE-84 4000 K IP65
Half the power, half the light. For a ceiling cove or a mirror cabinet, that is enough. IP65 stands for protection against water jets, and it is cut every 100 millimeters. Do not let the figure „total luminous flux 456 lm“ at ELV confuse you. What is meant is 456 lm per meter, as the technical data with 2,280 lm for 5 meters show.
Smart home: Homematic IP Lightstrip Set HmIP-LSS
A complete package of a 2-meter strip, controller and power supply, controllable via app, wall switch, Alexa or Google Assistant. It can be extended with one-meter pieces to a maximum of 10 meters. It does not work without an Access Point or hub; eQ-3 does not state a lumen value in the data sheet. If you want to make your own strips such as the FINE-69 smart, take the Homematic IP LED Controller HmIP-RGBW. According to the data sheet, it handles 2.1 amps per channel, so at 24 volts just over 50 watts. That is enough for around 5 meters of FINE-69 per channel. Which hub suits your household is covered in the guide to the smart home hub.
Philips Hue Lightstrip Plus V4
For households with Hue, the convenient route: Bluetooth or Bridge, according to Philips up to 1,700 lumens at 4000 K over 2 meters, cuttable and extendable to 10 meters. Philips states the color rendering as more than 80. That is enough for accents. At the countertop, we would rather go for the FINE-69 because of the color rendering. For light behind the TV with picture sync, there are dedicated solutions, compared in the guide to TV backlighting.
Govee COB Strip Light Pro
COB means chip on board: according to Govee, there are 1,260 LEDs on every meter, and the light appears as a continuous line without dots. Data according to the manufacturer: 450 lumens per meter, 24 volts, 72 watts for 5 meters, white from 2700 to 6500 K, Matter. It can be cut every 8 centimeters but cannot be extended. Govee does not state a protection rating or an Ra value, so it stays indoors.
Outdoors: tint Outdoor Lightstrip
Five meters with mounting clips, white from 1800 to 6500 K plus colors, controlled via Zigbee or remote, and according to ELV it can also be paired with a Hue Bridge. To be honest: IP44 means splash-proof, not waterproof. Under a roof overhang, that works; in a puddle, it does not. More on paths and facades in the guide to smart outdoor lighting.
For tinkerers: Diamex WS2812 LED strip
Here, each of the 240 LEDs gets its own controller and can be addressed individually, for chasing lights or small matrix displays. It is controlled via a microcontroller; according to ELV, the strip does not work with the HmIP-RGBW. The power draw is often underestimated. At full white brightness, each LED needs 60 milliamps according to ELV; 240 LEDs then draw 14.4 amps from 5 volts, or around 72 watts. A powerful power supply helps here, and for first experiments a unit with current limiting from the bench power supply guide (in German).
How we would decide
- Countertop, workbench, desk: Beneito FINE-69 in the P2-1 aluminum profile, 24-volt power supply with headroom, and if desired the HmIP-RGBW as a dimmer.
- Ceiling cove or bathroom: FINE-84 in IP65, because fewer lumens feel more pleasant here.
- Smart without tinkering: the Homematic set in a Homematic household, otherwise the Hue Lightstrip.
- An even line without a profile: the Govee COB.
- Garden: tint, but only in a sheltered spot.
- Programming your own effects: Diamex WS2812.
One last tip from Beneito’s manual: the adhesive tape only sticks reliably at an ambient temperature of about 10 °C or more. So in an unheated garage in winter, it is better to wait.
Frequently asked questions
What is the difference between 12 and 24 volts in LED strips?
At the same power, only half the current flows at 24 volts: 28.8 watts is 2.4 amps at 12 volts and 1.2 amps at 24 volts. Less current means less loss on the thin conductor tracks, so the end of a long strip is more likely to stay as bright as the beginning.
How big does the power supply for an LED strip need to be?
Multiply watts per meter by length and plan in headroom. 3 meters of FINE-69 come to 3 × 9.6 W = 28.8 W. Mean Well advises loading ordinary switching power supplies to only about 70 percent in most cases, which gives just over 41 W. So a 24-volt power supply with 50 watts fits.
How bright does an LED strip for the kitchen need to be?
Lumens per meter decide whether a strip actually lights something or merely decorates. According to ELV, the FINE-69 delivers 940 lumens per meter in warm white, the more economical FINE-84 around 456. That is roughly the difference between a countertop and a ceiling cove.
What color rendering should an LED strip have?
Ra 80 is enough for accent lighting. When chopping vegetables or soldering, Ra 90 makes a noticeable difference, because reds and skin tones do not look washed out. According to the data sheet, the Beneito strips reach more than 90, and according to Philips, the Hue Lightstrip more than 80.
Why does an LED strip need an aluminum profile?
Without a profile, you can see the individual light dots on glossy countertops. The P2-1 profile takes strips up to 12 millimeters wide, the matte cover diffuses the light, and the aluminum absorbs heat. A COB strip such as the Govee COB Strip Light Pro gets by without a profile.
Can LED strips be used outdoors?
Only with a suitable protection rating, because IP20 means dry indoor rooms. The tint Outdoor Lightstrip is rated IP44, so it is splash-proof but not waterproof and belongs under a roof overhang. The FINE-84 in IP65 is protected against water jets.
Sources
- ELV: Beneito FINE-69, 3000 K, IP20
- Beneito: FINE-69 data sheet
- Beneito: FINE-69 manual
- ELV: Beneito FINE-84, 4000 K, IP65
- ELV: Homematic IP Lightstrip Set HmIP-LSS
- eQ-3: HmIP-LSS data sheet
- eQ-3: HmIP-RGBW data sheet
- eQ-3: HmIP-RGBW manual
- ELV: P2-1 aluminum profile
- ELV: tint Outdoor Lightstrip
- ELV: Diamex WS2812 LED strip
- Philips Hue: Lightstrip Plus base kit V4
- Govee: COB Strip Light Pro
- Mean Well: Questions and answers on LED power supplies
Where to buy
- Beneito FINE-69 3000 K IP20View at ELVAvailable in Germany: ELV
- Beneito FINE-84 4000 K IP65View at ELVAvailable in Germany: ELV
- Homematic IP Lightstrip Set HmIP-LSSView at ELVAvailable in Germany: ELV
- Homematic IP LED Controller HmIP-RGBWView at ELVAvailable in Germany: ELV
- Aluminiumprofil P2-1View at ELVAvailable in Germany: ELV
- tint Outdoor LightstripView at ELVAvailable in Germany: ELV
- Diamex WS2812 LED-StreifenView at ELVAvailable in Germany: ELV
- Philips Hue Lightstrip Plus V4Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Govee COB Strip Light ProCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
