Contents11 sections
This guide was first published in German on handgetestet.de.
A drywall screwdriver does exactly one thing, and it does it stubbornly: it drives the screw to a preset depth and then stops. For a wall or ceiling made of gypsum boards, we consider the Bosch GTB 18V-45 the most balanced choice, because it is light, simply retracts its depth stop for backing screws out and can be upgraded later with a magazine. If you already have batteries from Makita, Festool, Metabo or Milwaukee on the shelf, stick with your brand.
Why not just use a drill/driver? Because every single screw has to sit just right. Rigips writes in its installation guidelines that the screw heads must not break through the paper facing. If the head sits too deep, the facing is damaged. If it sits too high, it gets in the way when applying joint compound. You can manage it with a regular cordless drill/driver, but only with a very delicate touch.
How many screws go into one room?
The number is surprising the first time. In its installation guidelines, Rigips specifies a maximum screw spacing of 250 mm for single-layer boarding on a wall, and a maximum of 170 mm on ceilings and sloped surfaces. A 2.50 m tall wall board therefore gets around eleven screws on each stud. With three studs behind the board, that is already more than 30, and that is for a single board.
Scaled up to an attic conversion, you quickly end up with several thousand screws. This is exactly where the tool plays to its strengths. The no-load speed of all five models is between 4,000 and 5,000 revolutions per minute. The screw is in within an instant. And then it stops, because the stop limits the depth.
Depth stop, magazine, battery: what really counts
The depth stop is the heart of it. Bosch describes the process in the manual: the stop sleeve touches the workpiece, the drive switches off, and the bit holder stops turning. You set the depth on a sleeve with a scale. Bosch advises determining the right setting with a test screw. We would follow that advice for every tool, ideally on an offcut of the same board.
A magazine attachment pays off as soon as you board out entire rooms. The screws then come on a strip, and your free hand holds the board. Bosch, Makita and Festool specify screw lengths of 25 to 55 mm for their attachments, Metabo 25 to 57 mm. For individual boards, repairs or cutouts, you work without a magazine anyway.
When it comes to torque, you should not compare the figures side by side. Festool gives separate values for wood and steel (5 and 14 Nm), Bosch and Metabo 6 Nm each, Milwaukee 13 Nm, and Makita states no figure online. For gypsum boards on thin profiles, any of these tools is enough. Weight overhead matters more. If you are screwing a ceiling, you hold the tool above your head for hours.
And the battery decides more than any line on a spec sheet. Bosch, Makita, Festool and Milwaukee also sell their tools without battery and charger. If the tool fits into your existing 18-volt system, you save yourself a second charger and a second set of batteries.
Five drywall screwdrivers side by side
Bosch GTB 18V-45
At 0.95 kg without battery, it is one of the light tools. Its special feature is the retractable depth stop: to back a screw out, you slide the adjustment sleeve back instead of pulling off the stop. In PowerSAVE mode, according to the manual, the motor only runs when you press the tool lightly against the workpiece. Bosch lists the GMA 55 magazine attachment as a matching accessory, but it is not included in the scope of delivery.
Makita DFS452
Makita relies on Push&Drive. The brushless motor only starts when you press the tool against the surface, which, according to the manufacturer, saves battery. At 4,000 revolutions, it is the slowest of the five, and at 1.5 to 1.8 kg including battery, it is no lightweight. On the other hand, the 191L24-0 magazine attachment fits without tools and handles drywall screws from 3.5 to 4.0 mm in diameter.
Festool DWC 18-4500
Even the Basic version comes complete: magazine attachment, depth stop, scaffold hook, three PH2 bits and a Systainer case; only the battery is missing. According to Festool, the depth can be adjusted without tools in 0.1 mm increments. In AUTO mode, the motor works without the main switch and only runs when it is needed. If you hang boards every day, you get a complete package here. For a single attic room, it is more tool than you need.
Metabo TBS 18 LTX BL 5000
At 5,000 revolutions, it is the fastest of the five. Metabo states 0.9 kg without and 1.3 kg with battery. The SPEED FIX 57 magazine is included. The switchable impulse mode is interesting: it lets you tighten screws that stick out without removing the depth stop. For long ceiling jobs, it would be on our shortlist.
Milwaukee M18 FSG and FSGC
The M18 FSG is available as a bare tool, the FSGC-202X as a kit with magazine attachment, batteries and charger. Milwaukee states 13 Nm and up to 4,500 revolutions. Thanks to AUTO-START, the motor only starts under counterpressure. The manufacturer does not state a weight online. If you already own M18 tools, this is the right choice. Newcomers will find more specifications for comparison with the other four.
The right screw and a safe substrate
Without the right screw, even the finest stop will not help. Rigips makes a clear distinction: drywall screws with fine thread for metal profiles up to 0.7 mm sheet thickness, screws with a drill point for thicker profiles up to 2.5 mm, and coarse thread for wooden substructures. On metal profiles, the manufacturer recommends 3.5 × 25 mm for single-layer boarding and 3.5 × 35 mm for double-layer boarding. With Rigips CW profiles, the screw should penetrate at least 10 mm through the profile. The drive is PH2. A few spare bits belong in your pocket; our guide to bit sets helps you choose.
Before the first screw, take a look inside the wall. In the manual, Bosch points out that suitable detectors should be used to locate hidden utility lines. If the screw hits a power line, according to Bosch, metal parts of the tool can also become live; so hold the tool by its insulated grip surfaces. According to the same manual, safety glasses are always part of the job. Which devices reliably find cables is covered in our guide to wall scanners.
How we would decide
- You are finishing a room and do not have a battery system yet: Bosch GTB 18V-45; you can buy the GMA 55 magazine later.
- Lots of ceiling, long days overhead: Metabo TBS 18 LTX BL 5000, light and with a magazine in the box.
- Drywall as a profession: Festool DWC 18-4500 with depth adjustment in 0.1 mm increments and complete accessories.
- Makita or Milwaukee batteries already on hand: DFS452 or M18 FSG respectively, ideally as a kit with magazine right away.
- Just a small furring wall: then your existing drill/driver is enough, as long as you set every screw with a careful touch.
Frequently asked questions
Why a drywall screwdriver instead of a cordless drill/driver?
Every screw has to sit just right: according to Rigips, the heads must not break through the paper facing, and a head that sits too high gets in the way when applying joint compound. The depth stop switches off the drive as soon as the depth is reached. With a drill/driver, that only works with a very delicate touch.
How many screws do you need for one gypsum board?
Rigips specifies a maximum screw spacing of 250 mm on walls and 170 mm on ceilings. A 2.50 m tall wall board therefore gets around eleven screws on each stud, more than 30 with three studs. For an attic conversion, that quickly adds up to several thousand.
Is a magazine attachment worth it?
As soon as you board out entire rooms, it pays off: the screws come on a strip, and your free hand holds the board. Festool and Metabo include the magazine; for Bosch, the GMA 55 is sold separately. For repairs and cutouts, you work without one anyway.
Which drywall screwdriver is suitable for ceiling work?
Overhead, weight counts more than torque. According to the manufacturer, the Metabo TBS 18 LTX BL 5000 weighs 1.3 kg with battery, has the SPEED FIX 57 magazine in the box and an impulse mode for tightening screws that stick out.
Which screws do you use for gypsum boards?
Rigips distinguishes fine thread for metal profiles up to 0.7 mm sheet thickness, a drill point for thicker profiles and coarse thread for wood. On metal profiles, the manufacturer recommends 3.5 × 25 mm for single-layer and 3.5 × 35 mm for double-layer boarding. The drive is PH2.
How do you set the depth stop correctly?
The depth is set on a sleeve with a scale. Bosch advises determining the right setting with a test screw, sensibly on an offcut of the same board. According to the manufacturer, Festool allows tool-free adjustment in 0.1 mm increments.
Sources
- Bosch Professional: GTB 18V-45, product page
- Bosch Professional: original operating instructions GTB 18V-45 (PDF)
- Bosch Professional: GMA 55 magazine attachment
- Makita: DFS452 cordless drywall screwdriver
- Makita: 191L24-0 magazine attachment
- Festool: DWC 18-4500 Basic
- Metabo: TBS 18 LTX BL 5000
- Milwaukee: M18 FSG
- Milwaukee: M18 FSGC with magazine attachment
- Rigips: drywall installation guidelines (PDF, in German)
Where to buy
- Bosch Professional GTB 18V-45Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Metabo TBS 18 LTX BL 5000Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Festool DWC 18-4500 (Basic, ohne Akku)Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Makita DFS452Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Milwaukee M18 FSGCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
Still undecided?
Keep comparing at your own pace – every article in this category is checked monthly for new and discontinued models.






