Contents10 sections
This guide was first published in German on handgetestet.de.
The box says 250 kg, and in the basement there are five shelves full of leftover tiles, paint buckets and crates of drinks. Do the math, though, and the unit does not actually hold five times 250 kg. The number that counts is called the bay load, and it is usually printed one line further down. For the garage and basement, we consider the Proregal Rivet in 180 × 120 × 60 cm the most sensible choice, because according to the manufacturer its shelf load and total load match up and the depth is enough for large boxes. In narrow basement corridors, the 90 cm wide Schulte unit is the better choice; for tools on the wall, the pegboards from raaco.
Shelf load, bay load and what the numbers leave out
The shelf load applies to a single shelf. The bay load applies to the entire bay, meaning all shelves between two frames combined. An example makes the difference tangible. For its heavy-duty unit with five wooden shelves in 180 × 90 × 40 cm, Schulte specifies a load capacity of 175 kg per level but a bay load of 700 kg. Five fully loaded shelves would come to 875 kg. That is more than the bay may carry.
Both values also only apply under certain conditions. META writes of its boltless shelving units that shelf and bay loads apply to evenly distributed loads, and that bay load figures only apply to runs of three bays or more. Schulte ties the load capacity to even distribution and to the unit being fixed to the wall. A single engine block in the middle of an MDF shelf is something else entirely than a layer of boxes reaching all the way to the edges.
- Check the bay load first, then the shelf load. For three of the five units below, the bay load is exactly the shelf load times the number of shelves; for the 90 cm wide Schulte, it is not.
- Choose the depth by what you store. A Euro container measuring 60 × 40 cm only fits lengthwise in a 60 cm deep unit; at 40 cm depth, it has to sit crosswise and needs 60 cm of width per box.
- Mind the height-to-depth ratio. From 4 : 1, META requires securing against tipping, by wall or floor anchoring. A unit 2 m high and 50 cm deep sits exactly at this limit.
- Assess the location honestly. In the instructions for the Rivet, Proregal lists a dry, regularly ventilated room and a level, non-slip floor as prerequisites.
One more thought on dynamic loads. The Proregal instructions explicitly rule out concentrated impact loads, as well as heavy items with a small footprint and items stored hanging. If you plan to heave wheel rims, jerrycans or a compressor onto the shelves, put the heavy things at the bottom. That is also how it appears there as a safety instruction.
Five shelving units and a tool wall side by side
Proregal Rivet 180 × 120 × 60 cm
Five MDF shelves at 250 kg each and a total load of 1,250 kg, according to the data sheet. So here the numbers add up. According to the manufacturer, the shelves can be set in 3.5 cm increments, and assembly with the boltless system takes about 20 to 25 minutes according to Proregal. The instructions themselves name two restrictions: the unit is intended for private use only, and all levels should be evenly spaced so that it stays stable. Proregal offers wall spacers and shelf connectors as accessories.
Schulte Schwerlastregal mit 5 Holzböden
Schulte’s heavy-duty unit with five wooden shelves is the narrow option for the basement. At 90 cm wide and 40 cm deep, it fits corridors where a 60 cm deep unit would block the way. Schulte states that the unit has been tested to twice its load capacity in accordance with BGR 234, a rule issued by the German statutory accident insurance institution (Berufsgenossenschaft), and says it manufactures in Germany. The shelves are particleboard. With a bay load of 700 kg, it is well suited to supplies, tool cases and binders, but not to packs of tiles on every level.
Schulte Schwerlastregal XXL 180 × 160 × 60 cm
Schulte’s XXL heavy-duty unit: four MDF shelves, 250 kg each, bay load 1,000 kg. Here too, the math works out. The 1.60 m width is both a blessing and a burden. Bulky items find room, while small ones disappear into the 60 cm depth. If you store small parts, you are better off with two narrow units.
Schulte FLEX Stecksystem
According to Schulte, the FLEX boltless system consists of two 90 cm bays and one 40 cm wide element, which can be connected in a row, as a corner unit or in a U shape. Because the angle profiles are split, one bay can also become two 90 cm high units, for example under a basement window. At 90 kg per shelf, however, it can bear considerably less than the other Schulte units here. That is enough for books, canned goods and cardboard boxes, but not for bags of cement.
META CLIP SET Steckregal
META, based in Arnsberg, Germany, mainly builds storage systems for commercial use, and you can tell from this boltless shelving system. The shelves can be adjusted in 25 mm increments and are perforated on a 50 mm grid for shelf dividers and partitions. There are also lip strips for loose items and storage bins. The system is expanded with add-on units that share a frame with the starter unit. According to the manufacturer, the set comes in a height of 2 m and depths of 40, 50 or 60 cm. META itself requires anti-tip securing from a ratio of 4 : 1; at 40 cm depth, wall anchoring is therefore a must.
raaco Werkzeug-Wandpaneel x 3 mit 44 Clips
Tools you reach for every day belong on the wall, not in a box. The raaco tool wall panel set consists of three galvanized pegboards measuring 156 × 44 cm together and 44 SuperClips made of steel and plastic. According to the manufacturer, the clips snap in without tools and can be repositioned freely. According to raaco, each board holds 75 kg. Compatibility is a practical bonus: according to raaco, the SuperClips fit pegboards with 34 or 38 mm hole spacing.
Whether the wall can take it is a separate question. Aerated concrete, hollow brick and drywall each need different anchors. Which ones is explained in our guide to wall anchor sets. And if you are planning the pegboard above a new work surface, you will find dimensions and load capacity in our workbench guide (in German).
Which shelving unit for which room?
- Garage with boxes, tires and garden tools: the Proregal Rivet 180 × 120 × 60 cm, with its back against the wall and the heavy items at the bottom.
- Tight basement corridor: the Schulte unit at 90 × 40 cm. Plan for no more than 140 kg per shelf, and the bay load of 700 kg is respected.
- Niche, corner or the space under a window: the Schulte FLEX, as long as nothing heavy goes on it.
- Workshop with screws, spare parts and plans to extend the shelving later: META CLIP with shelf dividers and add-on units.
- Hand tools: the raaco pegboards above the workbench. They do not replace a shelving unit; they take load off it.
One thing applies to every one of these units. Do not climb on them, not even on the bottom shelf. Proregal states this explicitly in its safety instructions. A boltless shelving unit is not a ladder.
Frequently asked questions
What is the difference between shelf load and bay load?
The shelf load applies to a single shelf, the bay load to all shelves between two frames combined. For its unit with five wooden shelves, Schulte specifies 175 kg per level but a bay load of 700 kg. Five fully loaded shelves would come to 875 kg, which is more than allowed.
Does the load capacity of a heavy-duty shelving unit always apply?
No, only under certain conditions. META specifies evenly distributed loads, and Schulte additionally requires the unit to be fixed to the wall. Proregal rules out concentrated impact loads, heavy items with a small footprint and items stored hanging. Heavy items therefore belong at the bottom.
How deep should a basement shelving unit be?
That depends on what you store. A Euro container measuring 60 × 40 cm only fits lengthwise in a 60 cm deep unit; at 40 cm depth, it has to sit crosswise and needs 60 cm of width per box. In tight corridors, a 40 cm deep unit is still often the only option.
When does a shelving unit need to be secured against tipping?
META requires securing with a wall or floor anchor from a height-to-depth ratio of 4 : 1. A unit 2 m high and 50 cm deep sits exactly at this limit; at 40 cm depth, wall anchoring is a must.
Which shelving unit fits a narrow basement corridor?
The Schulte heavy-duty unit, 90 cm wide and 40 cm deep. Schulte states that it has been tested to twice its load capacity in accordance with BGR 234, a German occupational safety rule. Plan for no more than 140 kg per shelf, and the bay load of 700 kg is respected.
How much can a tool pegboard hold?
For the raaco set with three galvanized pegboards, the manufacturer specifies 75 kg per board. The SuperClips snap in without tools and fit pegboards with 34 or 38 mm hole spacing. Whether the wall can take it depends on using the right anchors for aerated concrete, hollow brick or drywall.
Sources
- Proregal: Schwerlastregal Rivet heavy-duty unit 180 × 120 × 60 cm
- Proregal: Rivet assembly instructions and safety information (PDF)
- Schulte Regalwelt: Schwerlastregal mit 5 Holzböden 180 × 90 × 40 cm
- Schulte Regalwelt: Schwerlastregal XXL 180 × 160 × 60 cm
- Schulte Regalwelt: FLEX Stecksystem heavy-duty unit
- META: CLIP SET Steckregal
- META: CLIP Steckregal (system description)
- raaco: Werkzeug-Wandpaneel x 3 + 44 Clips
- raaco: Tool wall and SuperClip system
Where to buy
- Proregal Rivet 180x120x60 cmCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Schulte Schwerlastregal 5 Holzböden 180x90x40 cmCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Schulte Schwerlastregal XXL 180x160x60 cmCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Schulte FLEX StecksystemCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- META CLIP Steckregal 2000x1000x500Check price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- raaco Werkzeug-Wandpaneel x 3 + 44 ClipsCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
Still undecided?
Keep comparing at your own pace – every article in this category is checked monthly for new and discontinued models.






