Black Friday Woche läuft bis 30.11.: our pick in each buying guide
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,746 guides and reviews in German How we test
handgetestet

Bench grinder or wet sharpener? Why speed and grit are decisive, what matters when sharpening knives, and six machines compared.

handgetestet editorial team · Updated November 17, 2026
Scheppach Tiger 2000SImage: scheppach (press image)

Editorial selection based on research, not tested by us. Reasons and limitations are in the text.

Contents12 sections

This guide was first published in German on handgetestet.de.

A kitchen knife does not belong on a wheel spinning at 3,000 rpm. If you buy a bench grinder for everything, you will find that out at the latest with the first blade that heats up on the wheel. If it is mainly about knives, chisels and plane irons, you are better off with a slow-running wet sharpener, and among the machines for home use we consider the Tormek T-4 the most well-rounded choice. The double-wheel grinder is still useful. Just for other jobs.

Two machines, two worlds: 31 meters per second versus just over one

Doing the math helps. According to Metabo and Einhell, a 200 mm wheel on a double-wheel grinder turns at 2,980 revolutions per minute at no load, so its rim moves at around 31 meters per second. The stone of the Tormek T-4 has the same diameter but, according to the manufacturer, turns at 120 rpm. That works out to about 1.3 meters per second, roughly one twenty-fifth. On top of that, it runs through a water bath, which according to Tormek prevents the steel from overheating.

These numbers explain the division of labor. The bench grinder removes a lot of material quickly: mushroomed cold chisels, rounded screwdrivers, the dull blade from the lawn mower. It is too coarse and too hot for a fine edge, because a thin blade heats up on the fast dry wheel within seconds. The wet sharpener works slowly and in a controlled way. A bevel with a chip takes considerably longer on it.

Reading the grit: what K36, K60 and K220 mean

The smaller the number, the coarser the grit. Double-wheel grinders almost always come with a pair of K36 for reshaping and K60 for the finer pass. Wet stones start where the bench grinder leaves off: Scheppach supplies the Tiger 2000S with a K220 stone. Tormek takes a different approach. According to the manufacturer, the included SP-650 stone grader can change the surface of the original stone so that it grinds like 220 grit or roughly 1000. So if you do without a fine stone, you are not sacrificing sharpness, only convenience.

After the stone comes the leather. Both Tormek models and the Tiger 2000S have a leather honing wheel that you apply a polishing compound to. It removes the fine burr left on the edge after grinding. For kitchen knives, this step is the difference between „cuts“ and „glides through the tomato.“

Six sharpening machines side by side

ModelType and motorWheel and gritSpeed according to manufacturerBest forOffer (affiliate link)
Tormek T-4 OriginalWet sharpener, 120 W, 8 kgStone 200 × 40 mm, adjustable from 220 to 1000; leather 145 mm120 rpmKnives, chisels, plane irons at homeAvailable in Germany: Amazon.de
Tormek T-8 OriginalWet sharpener, 200 W, 14.8 kgStone 250 × 50 mm, adjustable from 220 to 1000; leather 220 mm100 rpmWoodturners, cabinetmakers, heavy jigsAvailable in Germany: Amazon.de
Scheppach Tiger 2000SWet sharpener, 120 W (S1), 8.6 kgStone 200 × 40 mm, K220; leather wheel120 rpmGetting started with wet sharpeningAvailable in Germany: scheppachAvailable in Germany: Amazon.de€94.99 at scheppach · As of 19.11.
Scheppach BG200WWet and dry grinder, 250 W (S1), 11.75 kgWet stone 200 × 40 mm K80; dry wheel 150 × 20 mm K60Motor 2,850 rpm, wet stone not specifiedCoarse grinding and touch-up sharpening on one machineAvailable in Germany: scheppachAvailable in Germany: Amazon.de€99.99 at scheppach · As of 19.11.
Scheppach BG150Double-wheel grinder, 370 W input, 9.8 kg2 × 150 × 25 mm, K36 and K602,980 rpmCold chisels, mower blades, deburringAvailable in Germany: scheppachAvailable in Germany: Amazon.de€89.99 at scheppach · As of 19.11.
Metabo BS 200 PlusDouble-wheel grinder with belt arm, 600 W, 16.9 kgWheel 200 × 25 mm, 60 N; belt 50 × 1000 mm, K602,980 rpmMetalworking, reshaping bladesAvailable in Germany: Amazon.de

Prices may change; the price shown by the retailer applies.

Want a second opinion before buying?Ask via WhatsApp

Tormek T-4 Original

Compact, 8 kilograms, and the essentials are already in the box: universal support, stone grader, the AngleMaster angle gauge and polishing compound. According to Tormek, the motor delivers 120 watts at 8.4 newton meters and is designed for continuous operation. For private users, Tormek grants an eight-year warranty if the machine is registered online; for commercial use, it is two years. In the manufacturer’s assessment, it is sufficient for knives, axes and chisels. According to Tormek, however, heavy jigs for drill bits or long planer blades can feel unstable on it.

Tormek T-8 Original

Bigger in every respect. The stone measures 250 × 50 millimeters, torque is 14.7 newton meters, and the kit additionally includes a jig for straight edges and a truing tool for the stone. According to Tormek, the eight-year warranty also applies to professional use. If you only look after a few kitchen knives, at 14.8 kilograms you are hauling quite a lot of machine down to the basement.

Scheppach Tiger 2000S

Same principle, simpler execution. Scheppach specifies an induction motor with 120 watts of continuous power, a 200 mm aluminum oxide stone with K220 and a shatterproof water tank; universal support, angle gauge and honing compound are included. There is no adjustable stone as with Tormek. That is enough to start with; if you want a finer finish later, you need a second stone.

Scheppach BG200W

On the left, a 200 mm wet stone with 80 grit above a one-liter water tank; on the right, a 150 mm dry wheel with K60. The idea makes sense: rough-grind first, then refine wet, without switching machines. Scheppach does not list the speed of the wet stone separately in the data sheet. K80 is also considerably coarser than the 220 of the dedicated wet sharpeners, so kitchen knives still need handwork on a honing stone.

Scheppach BG150

A typical bench grinder for the workbench: two 150 mm wheels, 25 millimeters wide, K36 and K60, no-load speed 2,980 per minute. According to Scheppach, a work light and an eye shield with magnifier are part of the equipment. Exactly right for cold chisels and mower blades. Not for knives.

Metabo BS 200 Plus

Instead of a second wheel, this one has a 480-millimeter belt arm with a 50-millimeter-wide sanding belt. Metabo specifies 600 watts input, an LED work light, tool-free belt changes and a 33-millimeter dust extraction port; the arm swivels 90 degrees. The belt is flat and runs over a long stretch, which makes straight bevels and derusting large surfaces easier. Metabo does not mention speed control.

Safe at the wheel: three millimeters, five millimeters, one minute

On a bench grinder, the tool rest is what counts. In its checklist for grinding machines, the DGUV (German Social Accident Insurance) states that the gap between the tool rest and the wheel may be no more than 3 millimeters wide, and no more than 5 millimeters are intended to the guard at the top. Because the wheel gets smaller when it is dressed, both gaps must be readjusted regularly. Vitrified-bond wheels are checked with a ring test before mounting, and every change is followed by a test run of more than one minute while the danger zone in front of the wheel is kept clear.

Based on experience, the same checklist considers hearing protection always necessary on grinding machines, and safety glasses wherever there is a hazard to the eyes in any case. Settled grinding dust should be removed with an industrial vacuum cleaner and not blown away with compressed air. We have put together suitable glasses in our safety glasses guide. The DGUV also lists close-fitting clothing. That applies at the slow wet stone, too.

Which machine for which drawer?

  • Kitchen knives, pocket knives and the occasional chisel: Tormek T-4 Original. The adjustable grit and the leather wheel replace a whole set of water stones.
  • First attempts at wet sharpening: Scheppach Tiger 2000S, knowing that a finer stone may be added later.
  • Woodturning, planer blades, daily work: Tormek T-8 Original, because of the larger stone and the sturdier base for heavy jigs.
  • Cold chisels, mower blades, deburring after cutting: Scheppach BG150.
  • If you want both in a small footprint: Scheppach BG200W.
  • Metal workshop with reshaping and derusting: Metabo BS 200 Plus.

A single knife does not call for a machine; a good manual sharpener is often enough, and models for that are in our knife sharpener guide. If, on the other hand, you look after entire sets of tools, our chisel guide has suitable irons for the wet stone.

Frequently asked questions

What is the difference between a bench grinder and a wet sharpener?

A 200 mm wheel on a double-wheel grinder turns at 2,980 rpm at no load, and its rim moves at around 31 meters per second. The stone of the Tormek T-4, which is the same size, reaches about 1.3 meters per second and runs through water. The bench grinder removes a lot of material quickly; the wet sharpener works slowly and in a controlled way.

Can you sharpen kitchen knives on a bench grinder?

This guide advises against it. The fast dry wheel is too coarse and too hot for a fine edge, and a thin blade heats up on it within seconds. Knives belong on a wet sharpener followed by a leather honing wheel; for a single knife, a good manual sharpener is often enough.

What do K36, K60 and K220 mean on grinding wheels?

The smaller the number, the coarser the grit. Double-wheel grinders usually come with K36 for reshaping and K60 for the finer pass. Wet stones start at K220, for example on the Scheppach Tiger 2000S. Tormek uses the SP-650 stone grader to change the surface of the stone so that it grinds like 220 or roughly 1000 grit.

Tormek T-4 or T-8: which one is enough?

For kitchen knives, pocket knives and the occasional chisel, the T-4 at 8 kilograms is enough. The T-8 has a 250 × 50 millimeter stone, more torque and a sturdier base for heavy jigs. It suits woodturners, planer blades and daily work, and according to Tormek the eight-year warranty also applies to professional use.

Is the Scheppach Tiger 2000S worth it for getting started?

It is enough for your first attempts at wet sharpening. Scheppach specifies 120 watts of continuous power, a 200 mm stone with K220, universal support, angle gauge and honing compound. There is no adjustable stone as with Tormek; if you want a finer finish later, you need a second stone.

What safety gaps apply on a bench grinder?

According to the checklist of the DGUV (German Social Accident Insurance), the gap between the tool rest and the wheel must be no more than 3 millimeters, and no more than 5 millimeters to the guard. Because the wheel gets smaller when it is dressed, both must be readjusted regularly. Every wheel change is followed by a test run of more than one minute, plus hearing protection and, where there is a hazard, safety glasses.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.

Still undecided?

Keep comparing at your own pace – every article in this category is checked monthly for new and discontinued models.

Share this guide

Price dropping? We'll let you know

Scheppach Tiger 2000S: We'll email you once when the price at scheppach is at least 5 % below €94.99.

Only active after you click the link in our confirmation email; ends after 180 days at the latest. Unsubscribe at any time via the link in the email. More in our Privacy policy.

Price dropping? We'll let you know

Scheppach BG200W: We'll email you once when the price at scheppach is at least 5 % below €99.99.

Only active after you click the link in our confirmation email; ends after 180 days at the latest. Unsubscribe at any time via the link in the email. More in our Privacy policy.

Price dropping? We'll let you know

Scheppach BG150: We'll email you once when the price at scheppach is at least 5 % below €89.99.

Only active after you click the link in our confirmation email; ends after 180 days at the latest. Unsubscribe at any time via the link in the email. More in our Privacy policy.