Black Friday week runs until November 30: our pick in each buying guide
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,750 guides and reviews in German How we test
handgetestet

Hot glue guns 2026: glue output, 110 to 200 °C, 7, 11 or 12 mm sticks, cordless or corded. Steinel, Bosch, Rapid and UHU compared.

handgetestet editorial team · Updated November 17, 2026

Editorial selection based on research, not tested by us. Reasons and limitations are in the text.

Contents13 sections

This guide was first published in German on handgetestet.de.

According to Steinel, a small craft glue gun manages around 3 grams of glue per minute, a workshop gun 20 grams. Almost seven times as much, and that is exactly what decides whether a cable edge along the baseboard holds in one go or whether you wait for more glue after every half meter. For home and workshop, we recommend a corded glue gun for 11 mm sticks such as the Bosch PKP 18 E. Cordless only if you already have a compatible 18-volt battery on the shelf.

Grams per minute, temperature, stick size: the three numbers on the box

Glue output first. For bows, felt and Christmas stars, 3 to 4 g/min is enough. If you glue trim, cable channels or cardboard boxes, you need 16 to 20 g/min; otherwise the start of the bead sets before the end is on the workpiece.

Then the temperature. Bosch and Steinel specify 200 °C for their large guns. Styrofoam melts away at that heat. That is what low-temperature guns such as the UHU Creative at 110 °C are for, or switchable cordless guns that go down to 130 °C. In the manual for the MobileGlue 3011, Steinel adds a trick: apply the glue to the base, not to the rigid foam.

Stick size often only becomes an issue when you buy refills. The usual sizes are 7 mm for small guns and 11 mm for large ones. Rapid offers the EG212 for 12 mm sticks, UHU the Creative Low Melt for its own oval cartridges. Steinel explicitly requires original Steinel sticks for its cordless guns. So if you already own a box of glue sticks, check the size first and then the gun.

Cordless or corded?

The corded gun is the sober choice. It takes longer to heat up, about 7 minutes each according to Bosch and Steinel, but then holds its temperature without a break. Steinel’s cordless guns are ready after about 2 minutes and, according to the manufacturer, run for up to 90 minutes on one charge. That helps on a ladder, in the garden or at a trade show booth. Without a battery you already own, however, the kit quickly turns into a decision about a whole battery system that has little to do with gluing. If you are torn between Bosch’s green DIY battery and the blue professional battery, our guide to battery systems explains the differences.

Small pen-style guns with a built-in 3.6-volt battery play in a different league. They heat up in seconds and fit in a drawer. At 3 g/min, they are not good for more than crafts.

Seven hot glue guns and what they can do

ModelPower and temperatureGlue output, stickBest forOffer (affiliate link)
Bosch PKP 18 ECorded, 200 °C, 7 min heat-up20 g/min, 11 mmHousehold, repairs, workshopAvailable in Germany: Amazon.de
Steinel GlueMatic 3011Corded, 45 W, 200 °C, 7 min16 g/min, 11 mmHousehold, decorating, 2 m cordAvailable in Germany: Amazon.de
Steinel MobileGlue 301118 V Bosch PFA battery, 130 / 200 °C, 2 min20 g/min, 11 mmOwners of green Bosch batteriesAvailable in Germany: Amazon.de
Steinel PRO MobileGlue 5011 AMP18 V AMPShare battery, 130 / 200 °C, 2 min20 g/min, 11 mmTrades using blue Bosch batteriesAvailable in Germany: Amazon.de
Rapid EG212Corded, 200 W during heat-up, 3 to 6 min250 g/h, 12 mmHobby room, simple repairsAvailable in Germany: Amazon.de
Steinel MobileGlue 1007-SBuilt-in 3.6 V battery, USB, 170 °C, 15 s3 g/min, 7 mmCrafts, gift wrapping, the kitchen drawerAvailable in Germany: Amazon.de
UHU Creative Low MeltCorded, 110 °C, 3 to 5 minoval cartridgesStyrofoam, soft PVC, craft cornerAvailable in Germany: Amazon.de
Want a second opinion before buying?Ask via WhatsApp

Bosch PKP 18 E

This is the gun we recommend to most households. According to the operating instructions, the PKP 18 E draws 200 W while heating up and 16 W while keeping warm, delivers 20 g/min and weighs 0.35 kg. Bosch includes an extra-long nozzle. The heat storage is practical: after heating up, the gun can be used briefly without the cord until the glue gets thicker. According to the manual, workpieces should not be colder than 5 °C; steel should be warmed beforehand, for example with a heat gun.

Steinel GlueMatic 3011

The successor to the GlueMatic 3002 works with 45 W and a fixed 200 °C. At 16 g/min, it sits just below the Bosch. Steinel specifies a heat-up time of 7 minutes, a 2 m cord and a three-year manufacturer’s warranty. A fine nozzle is available as an accessory.

Steinel MobileGlue 3011

This cordless gun runs on all batteries of the Bosch-led Power for All alliance. Two settings, 130 and 200 °C, are switched at the press of a button; an LED shows temperature and charge level. According to the manual, weatherproof PUR sticks are used on the 130 °C setting. Steinel also warns: when switching from 130 to 200 °C, the glue briefly runs much more fluidly. In the kit with a 2.5 Ah battery, the gun weighs 0.705 kg.

Steinel PRO MobileGlue 5011 AMP

Technically the sister of the 3011, only for the 18-volt AMPShare professional battery. Same temperatures, same 20 g/min, 0.54 kg. As a professional tool, it only comes with a one-year manufacturer’s warranty, according to Steinel. There is also a version for Metabo CAS, so pay close attention to the suffix in the name when buying.

Rapid EG212

Rapid specifies 250 grams of glue per hour, which is just over 4 g/min, with a heat-up time of 3 to 6 minutes and a weight of 0.26 kg. It also has an adjustable stand and a silicone guard on the nozzle. That is too little for trim. For model building, cardboard and small plastic repairs, it works.

Steinel MobileGlue 1007-S

Built-in battery, USB charging cable, hot after about 15 seconds. According to Steinel, one charge lasts up to 30 minutes, and the battery charges to 90 percent in around 3 hours. An Eco mode switches it off automatically. With 170 °C, 3 g/min and 7 mm sticks, it is a craft tool, not a replacement for the big gun.

UHU Creative Low Melt

At 110 °C, according to UHU, it also bonds Styrofoam and soft PVC. Press the parts together for 15 to 20 seconds; after about 2 minutes the joint can take a load, and full strength is reached after 2 hours. According to the manufacturer, the glue does not hold on PE, PP and PTFE. The drawback is in the details: the oval cartridges are only available for this system.

Hot stays hot: what manuals and accident insurers advise

Bosch and Steinel specify up to 200 °C for the nozzle and the glue. If a drop stays on your skin, both manuals say not to pull it off but to cool it immediately with cold water. For minor burns on hands and arms, the BG BAU (German statutory accident insurance for the construction industry) advises cold water for no more than ten minutes and not opening blisters; larger burns need medical treatment. According to the manual, children aged eight and over may only use the Steinel devices under supervision.

PUR sticks are a separate issue. According to the BG ETEM (German statutory accident insurance for the energy, textile and electrical industries), reactive PUR hot-melt adhesives contain small amounts of diisocyanates, which are released as vapor during hot processing and can trigger allergic respiratory and skin diseases. The BG ETEM recommends choosing adhesives that require no hazard labeling wherever possible. If you use PUR sticks, only work in well-ventilated rooms and without skin contact. The manual for the MobileGlue 3011 names dry, well-ventilated indoor spaces as the place of use anyway.

Which gun for which workbench?

  • Trim, cable channels, boxes and repairs around the house: Bosch PKP 18 E, or alternatively the Steinel GlueMatic 3011 with its longer cord.
  • Green Bosch batteries in the basement: Steinel MobileGlue 3011. Then the bare tool version without battery and charger is enough.
  • Blue professional batteries on the job site: Steinel PRO MobileGlue 5011 AMP.
  • Styrofoam, model landscapes and soft PVC: UHU Creative Low Melt.
  • Gift ribbon and small odds and ends: Steinel MobileGlue 1007-S or the Rapid EG212.

If you often work on models, our guide to model-building tools (in German) covers the rest of the setup. There, the hot glue gun is one helper among several, not the main tool.

Frequently asked questions

How much glue output does a hot glue gun need?

For bows, felt and Christmas stars, 3 to 4 g/min is enough. If you glue trim, cable channels or cardboard boxes, you need 16 to 20 g/min; otherwise the start of the bead sets before the end is on the workpiece.

Cordless or corded hot glue gun?

According to Bosch and Steinel, a corded gun takes about 7 minutes to heat up, but then holds its temperature without a break. Steinel's cordless guns are ready after about 2 minutes and run for up to 90 minutes. Without a battery you already own, the kit quickly turns into a decision about a whole battery system.

Which hot glue gun is suitable for Styrofoam?

A low-temperature gun. At 200 °C, Styrofoam melts away. The UHU Creative Low Melt works at 110 °C and, according to UHU, also bonds Styrofoam and soft PVC, but it needs its own oval cartridges. Switchable cordless guns go down to 130 °C.

Which glue sticks fit my hot glue gun?

The usual sizes are 7 mm for small guns and 11 mm for large ones. Rapid offers the EG212 for 12 mm sticks, UHU the Low Melt for its own oval cartridges, and Steinel requires original sticks for its cordless guns. So check the size of the sticks you already have first.

What should you do about hot glue burns?

According to Bosch and Steinel, do not pull the drop off; cool it immediately with cold water instead. For minor burns, the BG BAU (German statutory accident insurance for the construction industry) advises cold water for no more than ten minutes and not opening blisters. Larger burns need medical treatment.

What should you watch for with PUR glue sticks?

According to the BG ETEM (German statutory accident insurance for the energy, textile and electrical industries), reactive PUR hot-melt adhesives release small amounts of diisocyanates when processed hot, which can trigger allergic respiratory and skin diseases. Only work with them in well-ventilated rooms and without skin contact, and choose adhesives that require no hazard labeling wherever possible.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.

Still undecided?

Keep comparing at your own pace – every article in this category is checked monthly for new and discontinued models.

Share this guide