Black Friday Woche ab 19.11.: unsere Wahl je Ratgeber
Independent buying adviceEvery claim with a sourceNo paid verdictsIn 36 countries1,734 guides and reviews in German How we test
handgetestet

Buying Model Building Tools 2026: What RC Cars Really Need

Model building tools 2026: hex drivers from 1.5 to 3 mm, nut drivers, soldering station, hobby knife. Wiha, Arrowmax, HUDY, Wera, Weller and Ersa for RC models.

handgetestet editorial team · Updated November 17, 2026
Contents11 sections

This guide was first published in German on handgetestet.de.

The bit box with 60 attachments and a plastic handle often ends up in the shopping cart. On an RC car, it is of little help. What you need is a few tools that fit precisely, above all a good set of hex screwdrivers in 1.5, 2.0, 2.5 and 3.0 mm, such as the Wiha PicoFinish 42992. Add a nut driver for the nuts, a sharp knife and, as soon as you solder on connectors, a temperature-controlled soldering station.

Three hex sizes do most of the work

Arrowmax, HUDY, Wera and Wiha, in other words the tool sets from RC specialists, all cover the same range: 1.5 to 3.0 mm hex socket. Your model’s assembly instructions tell you which size it needs. With a ready-to-run model like those in our comparison of remote-controlled cars, you should check before the first spare part is due.

How often you end up wrenching even on ready-to-run models is shown by our hands-on tests: on the DEERC 300E, a body clip went missing in a rollover, and on the Hosim X08, the steering links gave out quickly. Spare parts and the right tools therefore belong in the case from the start.

That leaves the question of the tip. A ball end lets you work at an angle. It transfers less torque, however, and the risk of stripping the screw head increases. For motor mounts and suspension arms, a straight tip is therefore the right tool.

Length matters too. Precision screwdrivers have blades 40 to 60 mm long; RC tools are usually 120 mm long and thus reach deep into the chassis, for example to screws under the battery holder.

Nuts do not belong in pliers. According to HUDY, a 5.5 mm nut driver fits M3 nuts and 7.0 mm fits M4 nuts, such as the wheel nuts on many touring cars. Pliers slip and scratch rims. For cable ties and cotter pins, they are still useful; more on that in our overview of plier sets.

And the handle? An engraved aluminum handle looks nice. What really matters is whether the tip still seats cleanly after a hundred screws.

Seven tools for the model building bench

ModelTypeKey specs according to the manufacturerBest for
Wiha PicoFinish 42992Precision hex screwdrivers, 6 pieces with holder0.9 / 1.3 / 1.5 / 2.0 / 2.5 / 3.0 mm, blades 40 to 60 mmAlmost all model builders, including drones and servos
Arrowmax AM-410991RC hex drivers, 4 pieces1.5 / 2.0 / 2.5 / 3.0 × 120 mm, hollow honeycomb handle (retailer information)Anyone who regularly works on 1:10 cars
HUDY Limited Edition Allen WrenchRC hex driver, sold individually1.5 / 2.0 / 2.5 × 120 mm, handle made of 7075-T6 aluminumRacers who buy replacements individually
Wera Kraftform Micro 2069, 5.5 mmNut driverWrench size 5.5 mm, blade 60 mmAnyone with M3 nuts
Weller WE 1010Soldering station70 W soldering iron, 100 to 450 °C, standby, password protectionSoldering battery connectors and motor wires
Ersa i-CON Nano MK2Soldering station80 W, 150 to 450 °C, approx. 9 s heat-up timeAnyone who solders often and fast
Swann-Morton ACM SetHobby knife set3 handles, 13 carbon steel bladesBodies, decals, kits

Wiha PicoFinish 42992

Six precision hex screwdrivers from 0.9 to 3.0 mm, plus a holder. Wiha explicitly lists model building as an area of use. You rarely need the small sizes on a car, but you do on servos, cameras and mini drones. The blades are on the short side at 40 to 60 mm. If you would rather have a ball end, Wera offers the 2052/6 set with 1.5 to 3.0 mm, but you pay for it with less force on tight screws.

Arrowmax AM-410991

The classic RC tool. Four drivers with 120 mm blades, in exactly the sizes found on the chassis. According to the retailer’s description, they have spring steel tips with a titanium nitride coating and hollow handles in a honeycomb pattern. Going by retailer prices, the set sits in the same price range as the Wiha, but offers only four sizes. It shows its strengths if you take your car apart after every day at the track.

HUDY Limited Edition

HUDY makes tools specifically for RC racing. The Limited Edition drivers are sold individually, with a CNC-machined handle made of 7075-T6 aluminum and a 120 mm blade. That is something no set can do. You replace only the size you use constantly, usually 2.0 mm. As a complete kit, it gets expensive.

Wera Kraftform Micro 2069 (5.5 mm)

Inconspicuous, yet one of the most useful items on the list. Wera builds the nut driver with the same three-zone Kraftform Micro handle as its electronics screwdrivers, and the cap rotates freely. For 7 mm wheel nuts, you need a second tool. HUDY offers its own nut drivers for that.

Weller WE 1010

If you solder battery connectors or ESC wires yourself, you need heat reserves. On thick strands, small precision soldering irons quickly reach their limits. The WE 1010 has a 70 W iron, regulates from 100 to 450 °C and, according to Weller, lets you change the tip without tools even when hot. It takes about 28 seconds to go from 50 to 350 °C. Compared with the Ersa, it sits one price tier lower.

Ersa i-CON Nano MK2

80 W, and according to the manufacturer, up to 350 °C in about nine seconds. A 1.6 mm chisel tip is included. According to Ersa, you set up three preset temperatures via free PC software and an optional microSD card. That is handy when switching between fine receiver wires and thick battery connector solder joints. If you only solder occasionally, the Weller will do. More devices are presented in our overview of soldering stations.

Swann-Morton ACM Set

Swann-Morton from Sheffield makes surgical blades and offers its own line of hobby knives. The ACM Set contains three handles and 13 carbon steel blades. You use them to separate kit parts from the sprue, cut out decals and deburr edges. Blades are consumables. A dull one slips more easily than a sharp one. If plastic needs to be sanded or milled, a rotary tool such as the Dremel helps.

If you are still looking for the right car, scale, drive and battery are explained in the guide to buying an RC car.

Which tool for which model?

  • First RC car, ready-to-run model: The Wiha PicoFinish 42992 and the Wera nut driver in 5.5 mm. That gets you through most repairs.
  • Kit or regular racing: The Arrowmax AM-410991 or individual HUDY drivers in the sizes your chassis needs. The long blades save time with every rebuild.
  • Drone, model aircraft, electronics: The Wiha set with 0.9 and 1.3 mm, plus a soldering station. For FPV drones, soldering is almost unavoidable.
  • Soldering rarely or often: For occasional use, the Weller WE 1010 is enough. If you solder a lot and use the preset temperatures, go for the Ersa.
  • Bodies and plastic model kits: The Swann-Morton set and a supply of spare blades.

Which tools an RC buggy needs in everyday use can be seen in our review of the Hyper Go H16BM from AMEWI, with its sturdy chassis and spare parts.

Frequently asked questions

Which hex key sizes do you need for RC cars?

The tool sets from RC specialists all cover the same range: 1.5 to 3.0 mm hex socket. Your model’s assembly instructions tell you which size it needs. With ready-to-run models, it is worth taking a look before the first spare part is due.

Ball end or straight tip on a hex screwdriver?

A ball end lets you work at an angle but transfers less torque, and the risk of stripping the screw head increases. For motor mounts and suspension arms, a straight tip is therefore the right tool. RC tools are usually 120 mm long and reach deep into the chassis.

Which nut driver fits M3 and M4 nuts?

According to HUDY, a 5.5 mm nut driver fits M3 nuts and 7.0 mm fits M4 nuts, such as the wheel nuts on many touring cars. Nuts do not belong in pliers; they slip and scratch rims. For cable ties and cotter pins, pliers are still useful.

Which soldering station for battery connectors and motor wires?

On thick strands, small precision soldering irons quickly reach their limits; you need heat reserves. The Weller WE 1010 has a 70 W iron and regulates from 100 to 450 °C, which is enough for occasional soldering. If you solder a lot and use preset temperatures, go for the Ersa i-CON Nano MK2 with 80 W.

What do you need a hobby knife for in model building?

You use it to separate kit parts from the sprue, cut out decals and deburr edges. The Swann-Morton ACM Set contains three handles and 13 carbon steel blades. Blades are consumables; a dull one slips more easily than a sharp one.

Sources

Where to buy

Shop in:

Sale, delivery, warranty and product safety are the sole responsibility of the respective retailer and manufacturer. All information without guarantee; prices and availability may change.

Links marked as affiliate links earn us a small commission if you buy through them. The price stays the same for you, and our verdict stays independent. As an Amazon Associate we earn from qualifying purchases.