Lowest €179.99 (19.11.) · Highest €214.99 (10.11.)
Price watch Scheppach HBS261 at scheppach
- Today
- €179.99As of 19.11.2026
- Lowest price, 30 days
- €179.99last on 19.11.2026
- Typical price (median), 30 days
- €214.99
- Days measured
- 910.11.–19.11.2026
Price dropping? We'll let you know
Contents12 sections
This guide was first published in German on handgetestet.de.
A wood band saw is not a metal saw, even though both go by the same name. If you cut wood and mostly saw curves, toys or small parts, a benchtop band saw such as the Scheppach HBS261 will serve you well. If you want to resaw planks, you need more cutting height, and if you want to shorten steel tubing, you need a completely different machine. Before you compare data sheets, you should therefore answer one single question. What will end up on the table?
The difference lies in the blade speed. According to the manufacturers, the wood band saws in this comparison run at 360 to 1,000 meters per minute. Holzmann’s BS128HDR metal band saw works at 23, 34 or 54 meters per minute. That is not a detail; it is a different world. In its manual, Einhell explicitly approves its TC-SB 245 L for wood, plastics and non-ferrous metals, such as aluminum or brass. Hardened metal is excluded there.
Path 1: Curves, toys and small parts made of wood
Here, cutting height matters less than the advertising would suggest. A rocking horse made of 18 mm panels or Christmas stars made of pine strips do not need 170 mm. A value of around 100 to 130 mm at 90 degrees covers that. You do not need more. More important is the throat depth, meaning the distance between the blade and the machine’s column. At 245 mm, a board just under a quarter of a meter wide can still be turned freely.
For tight curves, a simple rule from the Holzmann manual applies: small radii with narrow blades. The two benchtop models accept blades from 6 mm. In its manual, Einhell advises first rough-cutting curves about 6 mm beside the line. If a curve is too tight for the mounted blade, relief cuts up to just short of the line help. The offcuts then fall out one by one instead of pinching the blade. For cutouts in the middle of a panel, however, the band saw is still the wrong machine; that is what a good jigsaw (in German) is built for.
Path 2: Resawing planks and building furniture
Resawing means splitting a board on edge, for example to get two thinner panels with book-matched grain from a 16 cm wide oak plank. For that, the cutting height must be greater than the width of the board. A benchtop band saw with 101 mm quickly reaches its limit here. According to the manufacturers, the floor-standing machines from Holzmann and Scheppach manage 165 and 170 mm.
With the height, the wheels, blade width and weight also grow: both floor-standing models have wheels 315 mm in diameter and a considerably longer blade of 2,240 mm, and they accept blades up to 15 mm wide, while the benchtop saws stop at 12 or 13 mm. There is a practical reason for this. Solid wood deflects a narrow blade along the grain, while a wide blade runs straighter, according to the HBS300J manual. A fine tooth pitch produces cleaner surfaces but costs speed. Also expect a machine weight of 56 to 78 kg and a dust port 100 mm in diameter. A sturdy workbench (in German) next to it takes the resawn pieces. Straight rip cuts in panel material, on the other hand, are done faster and more accurately by a table saw.
Path 3: Steel, tubing and profiles
Metal requires slow blades, bi-metal or HSS blades, and a workpiece held firmly in the vise. Holzmann clearly assigns the three speeds of the BS128HDR: 23 m/min for stainless steel and alloy steel, 34 m/min for structural steel, 54 m/min for brass and aluminum. For the tooth pitch, the manual gives a rule of thumb. At least three teeth should be in the material at the same time; the thinner the wall, the finer the blade. So a thin-walled square tube needs more teeth per inch than a solid bar.
There are two designs to choose from. The stationary horizontal saw lowers the saw arm in a controlled manner and switches itself off after the cut. The handheld band saw, by contrast, weighs just over 13 kg. It comes to the workpiece, not the other way around. For cut edges on sheet metal and profiles, an angle grinder (in German) is then helpful for deburring.
Six band saws side by side
All values according to the manufacturers. Two versions of the HBS261 are on the market, including an older one with 120 mm cutting clearance and different speeds. Check the item number in the listing.
Einhell TC-SB 245 L
The smallest saw in the field, with a 400-watt induction motor, LED work light and a table that, according to Einhell, tilts from minus 2 to 45 degrees. Blades from 6 to 12 mm fit. The blade guard can be adjusted in height without tools. At just under 25 kg, it fits on a workbench. The height is not enough for resawing.
Scheppach HBS261
Same throat depth as the Einhell, but 130 mm cutting height and two speeds you can switch between depending on the wood and the desired cut surface. The die-cast aluminum table measures 307 × 315 mm and can be extended to 520 mm. Scheppach specifies 550 watts input; the continuous output in the data sheet is 370 watts. For hobbyists who occasionally cut a thicker square timber, this is our suggestion.
Scheppach HBS400
A floor-standing machine with a 545 × 400 mm cast iron table, a 750-watt motor and 170 mm cutting height. According to Scheppach, a stand with wheels, rip fence and table extension are included. The 56 kg take two people to move during assembly. If you resaw, this is where you get the most height in this comparison.
Holzmann HBS300J (230 V)
A similar class, different priorities. The cast iron table is extendable, the machine stands on a mobile base and weighs 78 kg. Holzmann specifies 165 mm cutting height, 305 mm throat depth and 750 watts of continuous output. The product page and the manual differ on the permissible blade width. Stick to 6 to 15 mm.
Holzmann BS128HDR (230 V)
A horizontal metal band saw with a base, a saw head that swivels from minus 45 to plus 60 degrees and a hydraulic cylinder that controls the lowering speed of the arm. According to the manufacturer, it handles round stock up to 125 mm. A limit switch stops it after the cut. If you cut a lot of stainless steel, take a look at its sibling, the BS128COOL with a coolant unit.
Scheppach MBS1200
Handheld or on a stand sold separately. A dial adjusts the blade speed continuously from 0.7 to 2.4 meters per second. Two blades with 10 and 14 teeth per inch are included. Scheppach names materials from PVC to stainless steel and cross-sections up to 127 × 127 mm. For repetitive cuts in a row, the stationary saw is more convenient.
How we would decide
- Curves, model making, small parts made of wood: Scheppach HBS261, or the Einhell TC-SB 245 L if 101 mm is definitely enough.
- Resawing and furniture making: Scheppach HBS400 or Holzmann HBS300J. If you need the mobile stand, go with the Holzmann.
- Steel profiles and tubing in a permanent workshop: Holzmann BS128HDR.
- Metal on the construction site or on location: Scheppach MBS1200.
Three key steps from the manuals apply to every one of these saws. The upper blade guide sits 2 to 3 mm above the workpiece. Push narrow pieces with a push stick. And after work, de-tension the blade, otherwise it will stretch over time. Einhell also requires hearing protection and a dust mask.
Frequently asked questions
Can you cut metal with a wood band saw?
Only to a limited extent. According to the manufacturers, the wood band saws in this comparison run at 360 to 1,000 meters per minute, the BS128HDR metal band saw at 23, 34 or 54 meters per minute. Einhell approves the TC-SB 245 L for wood, plastics and non-ferrous metals such as aluminum or brass; hardened metal is excluded.
What cutting height does a band saw need?
For curves and small parts cut from panels, a value of around 100 to 130 mm at 90 degrees is enough. For resawing, the cutting height must be greater than the width of the board, so a 16 cm wide plank needs more. According to the manufacturers, the floor-standing machines from Holzmann and Scheppach manage 165 and 170 mm.
Which blade width is suitable for tight curves?
According to the Holzmann manual, the rule is: small radii with narrow blades. The benchtop models accept blades from 6 mm. Einhell advises first rough-cutting curves about 6 mm beside the line and making relief cuts where the curves are too tight. For resawing, on the other hand, a wide blade runs straighter, because solid wood deflects narrow blades.
What does throat depth mean on a band saw?
Throat depth is the distance between the blade and the machine's column. It determines how wide a workpiece can be while still turning freely. At 245 mm, as on the Einhell TC-SB 245 L and the Scheppach HBS261, that is a board just under a quarter of a meter wide; the floor-standing machines offer 305 mm.
Which blade for metal tubing and profiles?
Metal requires bi-metal or HSS blades and a firmly clamped workpiece. As a rule of thumb, the Holzmann manual says at least three teeth should be in the material at the same time. The thinner the wall, the finer the blade, so a thin-walled square tube needs more teeth per inch than a solid bar.
What should you watch out for when working at a band saw?
The manuals name three key steps: the upper blade guide sits 2 to 3 mm above the workpiece, narrow pieces are guided with a push stick, and after work the blade is de-tensioned so that it does not stretch. Einhell also requires hearing protection and a dust mask.
Sources
- Einhell: TC-SB 245 L, product page
- Einhell Service: TC-SB 245 L, technical data and operating manual
- Scheppach: Bandsäge HBS261
- Scheppach: Bandsäge HBS400
- Scheppach: Metallbandsäge MBS1200
- Holzmann: Holzbandsäge HBS300J_230V and operating manual
- Holzmann: Metallbandsäge BS128HDR_230V and operating manual
Where to buy
- Scheppach HBS261€179.99≈ £149.91≈ CHF 166.36≈ PLN 794.08≈ SEK 2,005.63≈ DKK 1,345.32≈ NOK 1,908.70≈ CZK 4,389.24≈ HUF 66,308≈ RON 962.35≈ ISK 24,659≈ $197.41≈ CA$282.40 at scheppach · As of 19.11.View at scheppachAvailable in Germany: scheppachCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Einhell TC-SB 245 LCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Scheppach HBS400€499.99≈ £416.44≈ CHF 462.14≈ PLN 2,205.86≈ SEK 5,571.39≈ DKK 3,737.13≈ NOK 5,302.14≈ CZK 12,192.76≈ HUF 184,196≈ RON 2,673.30≈ ISK 68,499≈ $548.39≈ CA$784.48 at scheppach · As of 19.11.View at scheppachAvailable in Germany: scheppachCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Holzmann HBS300J 230 VCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Holzmann BS128HDR 230 VCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
- Scheppach MBS1200€179.99≈ £149.91≈ CHF 166.36≈ PLN 794.08≈ SEK 2,005.63≈ DKK 1,345.32≈ NOK 1,908.70≈ CZK 4,389.24≈ HUF 66,308≈ RON 962.35≈ ISK 24,659≈ $197.41≈ CA$282.40 at scheppach · As of 19.11.View at scheppachAvailable in Germany: scheppachCheck price at Amazon.deCheck price at Amazon.co.ukCheck price at Amazon.nlCheck price at Amazon.com.beCheck price at Amazon.frCheck price at Amazon.itCheck price at Amazon.esCheck price at Amazon.plCheck price at Amazon.seAvailable in Germany: Amazon.de
Still undecided?
Keep comparing at your own pace – every article in this category is checked monthly for new and discontinued models.







